CMXGKAMDE25C (41ADE25C793) Craftsman Edger - Overview
Sections of the CMXGKAMDE25C
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
SCREW:10-32X.562:#8P
PartSelect #: PS18442924
Manufacturer #: 1964
This is a genuine OEM sourced replacement housing screw designed for Ryobi and Troy-Bilt trimmers and blowers. It is commonly utilized to secure the starter housing. Please note, this metal housing sc...
No Longer Available
EDGER BLADE
PartSelect #: PS18485685
Manufacturer #: 797-00045
This is a genuine OEM sourced replacement part designed for use with trimmers/edgers. It is great for edging level ground around sidewalks and driveways. This blade is made out of metal and it is sold...
No Longer Available
Questions And Answers for CMXGKAMDE25C
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CMXGKAMDE25C
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Engine stops after a few seconds or minutes
Fixed by
these parts
these parts
Show All
Engine revs but trimmer head will not turn
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Fuel line broke
Removed the two screws holding the fuel tank to the main unit. Removed the two fuel lines and any stuck on rubber. Installed and installed two screws to mount the new tank. Slid fuel lines on their respective connectors. Done.
Parts Used:
-
Erik from ROBERTSDALE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
string trimmer would not start
emptied fuel from tank. pulled off the 2 fuel lines from the carburetor.opened the air cleaner door. removed the 2 torque screws that hold on the carburetor. removed the carburetor and air cleaner gasket. installed new carburetor and gasket and put back and tightened the 2 torque screws. closed air cleaner door and pushed the fuel lines onto the new carburetor.put some fuel in the tank. started the trimmer. runs great.
Parts Used:
-
john from SHARPSVILLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Trimmer Would Not Start
The replacement of the carburetor, O-ring, and gasket was simple. I removed 2 screws that held the air cleaner and carburetor in place, swapped them out, and replaced the screws. What took longest was finding a piece of fuel line after breaking one of them. It was brittle after hanging in my garage for several years. I found some in my garage and replaced it. It took a few pulls to get it started, but ran very smooth.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Additional information: rather than mixing my fuel, I purchased 40:1 pre-mix fuel to prevent gunking up the carburetor in the future. I use it in my other trimmer and have not had any issues.
Parts Used:
-
Ricardo from FORT WORTH, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!