All Installation Instructions for Jenn-Air Cooktop C201

replaced filter

pulled old one out , cleaned the area & replaced with the new one.

Parts Used:

Range Grease Filter

ELOISE from MILFORD, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

486 of 513 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old grease filter that I actually did not know I had to change

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

Parts Used:

Range Grease Filter

deborah from fort pierce, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

451 of 540 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Stove top element not working due to bad receptacle.

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Parts Used:

Surface Burner Receptacle Kit

Richard from Carthage, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

194 of 214 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My Jenn-Air is an "antique." The filter was disgusting!

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Parts Used:

Range Grease Filter

marion from aspen, CO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

168 of 324 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Cooktop was looking old and worn though there was no working problem.

All of the "old" pieces were very easily removed and replaced with the new pieces. The update looks terrific and works just fine!

Parts Used:

Delta Frame Surface Unit - 8 Inch

Delta Frame Surface Unit - 6 Inch

Range Grease Filter

Surface Burner Knob Kit

Donna from Charlotte, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

150 of 298 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Falling apart 20 year old grease filter for downdraft counter rangetop

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

Parts Used:

Range Grease Filter

Roe from Raleigh, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

147 of 289 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner had no temperature control other that full on.

Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).

Pull off the control knob.

Remove 2 screws that hold in control pannel.

Lift out the control pannel to the extent that the wires will let you. (2-3 inches)

Remove the nut that holds the switch/controller in the pannel.

Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.

Re-install the switch in the pannel.

Re-install the pannel in the stove.

Close breaker and test burner contol.

Parts Used:

Surface Unit Infinite Switch Kit

Eric from North Andover, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

63 of 72 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wanted to update surface parts to a very old (27 yrs?) Jenn-air range on an island

The first task was to find the rings, drip bowls and elements on the "PartSelect" webpage. It was surprising easy, especially since I have no experience whatsoever in replacing range parts. The ordering was straight-forward, and most of the parts arrived within a week, a couple were back-ordered, but arrived a week later. Instillation was easy - just unplug elements, lift parts out, and insert new parts. I made a mistake in ordering - for the left side of the range, no adaptor rings are needed. I returned these excess parts to PartSelect, and within a week, they refunded the costs of these parts. Overall, I'm very please with the parts and service.

Parts Used:

Chrome Trim Ring - 6 Inch

Chrome Trim Ring - 8 Inch

Delta Frame Surface Unit - 8 Inch

Delta Frame Surface Unit - 6 Inch

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

george from burke, AL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

60 of 67 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Wanted to "renew" cook top

The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.

Parts Used:

Surface Burner Knob

Delta Frame Surface Unit - 8 Inch

Delta Frame Surface Unit - 6 Inch

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Surface Burner Receptacle Kit

Lucille from Mattoon, IL
Difficulty Level:
Difficult
Total Repair Time:
15 - 30 mins

33 of 43 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

blower motor died

Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!

Parts Used:

Indicator Light Kit

Blower Motor

Range Exhaust Vent Blower Wheel

Janellen from Aiken, SC
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench set

37 of 58 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lettering on old stove knobs was no longer visible and knobs were loose.

Took the old knobs off and replaced them with the new!

Parts Used:

Surface Burner Knob

Chris from Poway, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

26 of 31 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Just ugly this time`

It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.

Parts Used:

Grate - Kit of 2

Susan from Chino, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

24 of 26 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The drip bowls were old and stained; the knobs were so worn that they could hardly be read.

OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.

Parts Used:

Surface Burner Knob

Drip Bowl - Chrome - 8 Inch

Drip Bowl - 6 Inch

Mary Jo from Minford, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

13 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner was out but the burner coil worked on onother burner

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

Parts Used:

Surface Burner Receptacle Kit