AK2H30E2 (P1131557N) Amana Cooktop - Overview
Sections of the AK2H30E2
[Viewing 2 of 2]
Keep searches simple, eg. "belt" or "pump".
Range Installation Screw
PartSelect #: PS11741612
Manufacturer #: WP3400882
This screw is sold individually.
$10.20
In Stock
Order within the next 7 hrs and your part ships today!
Infinite Switch
PartSelect #: PS12347313
Manufacturer #: W11121639
$130.71
In Stock
Order within the next 7 hrs and your part ships today!
Refrigerator Screw
PartSelect #: PS11742713
Manufacturer #: WP488234
This screw is sold individually.
Size: 8-32 x 1/4 inch.
$11.57
Special Order
Dual Radiant Element with Limiter
PartSelect #: PS11764926
Manufacturer #: W10823726
With the dual element you are able to adjust the size of the burner you want to use to match your pots/pans.
$268.72
Special Order
Electric Hole Cover
PartSelect #: PS11757450
Manufacturer #: WPY0307427
This hole cover is almost two inches in diameter. It fits below the surface burner knob of some ranges, and has a center hole just big enough for the knob's shaft.
$16.58
Special Order
Surface Ribbon Element with Limiter - Small
PartSelect #: PS11741007
Manufacturer #: WP32082801
This is a 1200 watt / 240 volt surface element.
No Longer Available
Infinite Switch Knob - black
PartSelect #: PS11740815
Manufacturer #: WP31760601B
This infinite switch knob is just over two inches in diameter. It is all black in color and is made of plastic. This knob has light gray lettering denoting the off, low, medium low, medium, medium hig...
$55.83
Special Order
Surface Burner Switch
PartSelect #: PS2192651
Manufacturer #: Y0307429
This switch controls the stove top surface burner.
No Longer Available
Questions And Answers for AK2H30E2
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AK2H30E2
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Outer Heater ring not working on dual burner.
Turned off power to unit.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Tilted up Glass top and removed two screws holding rear hinges to range. Then I unplugged wire harness from lower range and placed the Glass top facing down on counter top with towel for cushion. Removed 1 screw holding center of burner to support frame, two alignment screws on perimeter, and two screws holding support frame to glass top. This allowed me to slide out the old element with all wiring connections intact.
Placed the new assembly in same location under support frame, noting numbered positions of two alignment screws from old unit. This is necessary to properly align heater to surface glass. Replaced all screws connecting burner to frame. Then I removed each wire one-by-one from old unit, reconnecting to same location on new unit.
Replaced top in reverse order from removal. Powered on the circuit breaker and verified proper operation of dual unit with large/small selecttor switch. Total time to repair about 30 minutes.
Parts Used:
-
Mark from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
24 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Inner burner of dual burner element burned out
Pulled stove out and unplugged it (energized wire at burner even with burner turned off) Removed screws to lift cook top Removed burner support brace Removed three screws to remove burner Removed connections from old burner, installed on new burner Replaced screws in burner to brace Replaced burner brace Lowered cook top and installed screws Plugged in stove and pushed it into space
Parts Used:
-
Don from Red Wing, MN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The infinite switch controlling one of the range top burners failed.
1 - Turned off electricity to the cook top.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which the infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.
All in all the part was an exact replacement and the repair went really well.
2 - Removed the range top from the cutout in the counter.
3 - Removed the smooth top by removing the screws around the perimiter of the smooth top.
4 - Removed the screws securing the corner closest to the dead switch.
5 - Removed the screws holding the channel, onto which the infinite switched were attached, to the frame of the cooktop base.
6 - Removed the dead switch by removing the screws that hold it to the channel.
7 - One by one move the wires from the old switch to the new one.
8 - Reversed the process, 6 - 5 - 4 - 3 - 2 - 1, to put the cook top back together.
All in all the part was an exact replacement and the repair went really well.
Parts Used:
-
erik from chester springs, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
12 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!