This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 20 mins and your part ships today!
This part is essential in your dishes getting clean during the wash cycle. If there is any debris or a tear in the filter, it can cause extra buildup and, therefore, causing dirty dishes.
$173.94
In Stock
Order within the next 20 mins and your part ships today!
The docking station is located on the water supply tube at the far back. It provides water to the upper and middle spray arm and also includes the flappers.
This part is the replacement wash arm cap, also known as the spray arm nut, for your dishwasher. It is made of white plastic and is approximately ½ an inch in diameter. The wash arm cap fastens the lo...
$14.73
In Stock
Order within the next 20 mins and your part ships today!
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
Order within the next 20 mins and your part ships today!
This is the replacement water valve for your dishwasher. The water inlet valve connects to the water source and solenoid wires, and ensures the tub has the right amount of water entering it. If your d...
$129.99
In Stock
Order within the next 20 mins and your part ships today!
unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....
Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.
Great pictures of components on this website confirmed what part to order.
Shut off water feed to DW and disconnect power to DW.
Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.
Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.
Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.
Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.
Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.
You have to pull the dishwasher out from underneath the counter and set it on its side. Before removing, I used a shop vac to remove any standing water from inside the dishwasher. Once I pulled out the dishwasher, I then tilted the dishwasher forward to let remaining water fall on the floor, again, using the wet vac for clean up. After it is on its side, I used a socket wrench to remove the one bolt that holds the drain valve on. Then I used a socket wrench to loosen the clamp for the drain hose and removed the hose. You then need to turn the entire drain valve 1/4 of a turn counter-clockwise to remove the old drain valve. Once it is off, remove the bracket from the old drain and attach it to the new drain valve using a phillips screwdriver. Before I reassambled the drain valve, I used my wet vac to remove any debree from where the drain valve connects to the dishwasher. Reverse the prior steps to install new drain valve and install dishwasher back under the counter. I tested the unit before installing the dishwasher back under the counter to insure it fixed the problem. The hardest part about doing this, was actually taking the dishwasher out from under the counter, very easy process in general. One thing I couldn't figure out about my original problem of the water not completely draining out, is why would the drain valve start draining the water then after 20 seconds it would stop? I couldn't find the answer, so I assumed the drain valve is like a 2 stage system and took a chance on replacing the drain valve; it worked.
