This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
If your washer’s detergent drawer is hard to open or the handle frame is damaged, this replacement part offers a quick fix. It snaps easily into place and helps restore smooth access to the dispenser....
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
If your front-load washer is leaking or smells musty, the door seal might be the problem. This rubber gasket fits between the door and the tub to keep water from spilling out during a cycle. It’s a ge...
This water inlet valve controls the flow of water into your appliance, ensuring proper filling during wash cycles. Ideal for replacing a faulty valve that causes leaks or filling issues, it restores e...
Your washer's door glass panel is the window to efficiency and cleanliness. If it's compromised, it may affect your appliance's performance. That's where our genuine Frigidaire Door Glass Panel comes ...
This washer tub-to-pump hose, often called a coin trap or bellows hose, carries water from the outer tub to the drain pump during drain and spin cycles. Designed with an integrated trap, it captures c...
When you're dealing with an ineffective washing machine, our Frigidaire Boot Seal Retaining Ring can be the solution you need. This is more than just a replacement part- it's about making your machine...
$58.30
In Stock
Questions And Answers for 970L48422E0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Peter
December 16, 2019
Washer has mold on inside of the gasket what do you recommend to use to clean regards
For model number 970L48422E0
Hello Peter, thank you for your question. We would recommend removing the gasket and cleaning it with soap, water and javex. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Vikki
November 27, 2019
Can the front loading washing machine door be reversed on this machine. From right to left opening.
For model number 970L48422E0
Hello Vikki, thank you for your question. The door is unable to be reversed because of the locking system in the machine. Sorry!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Edwin
February 24, 2020
Kenmore front load washer wont spin even in spin and rinse,everything else works,sometimes you can see timer change also
For model number 970L48422E0
Hello and thank you for writing.
It certainly sounds like it could be a faulty door lock and switch assembly PS12364048 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
Door lock takes a beating due to flimsy washer door which does not align well and subsequently gets slammed each time which causes lock to malfunction telling the washer that it is not locked. Due to safety the washer will not go into the spin mode. Remove top lid (2 screws) open washer door and loosed the 2 screws holding the lock assembly in place. Reach down into the washer and unsnap the 3 wire harnesses. Reverse to reinstall. Very easy.
