79631433710 Kenmore Washer - Instructions

1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable supplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.

Did the repair Myself. Saved $ 400.00 in the process.

I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.

The problem was the valve suppling water to the bleach dispenser was not closing completely. This also caused some water leaking towards
the front of the washer. Replacing the entire valve assembly was very
easy. Unplug the washer, turn off the water, remove the 2 screws that attach the control panel, disconnect the water supplies, unplug the 5 solenoids, remove the hose clamps from the 2 hoses, remove the 3
screws that attach the valve assembly and remove it. Reassemble in reverse order, I did find that applying some water based personal lubricant to the 3 high pressure seals made assembly much easier.

After getting the model info from the back of the washer control panel, I searched Partselect for the water valve part. Easy process, It was here in 2 days. Unplug the machine, I took 2 screws out of the back of the control console and tipped it forward to reveal the valve assy. Turn off the water at the wall and disconnect the hot and cold lines from the washer . I removed the 3 screws holding the valve assy to the deck and with pliers disconnected the 2 clamped rubber lines and then with just finger pressure wiggled the valve from the remaining pipe connections. I swapped the 5 wire connectors to the new valve and wiggled it back into place. Clamped the 2 rubber lines again. and then connected the water inlet hoses to the new valve. Closed it up and called the laundry lady ( sorry honey) 30 minutes to Household harmony again!!

Replaced valve body, very easy to fix as per the video, runs normal.

I noticed that my washer was leaking water into the tub. It was dripping, very slowly, but it was dripping. I noticed first, because it was starting to smell, and I didn’t understand why. Once I noticed that it was dripping, I checked online and noticed that the solenoid water inlet is most likely the problem. I found the part on parts, select, and confirmed with my model. The pictures were very close and similar, so I was pretty sure I was getting the cracked part. Once I received the part, it was time to fix it. You just have to turn the water supply off, remove the inlet lines with a adjustable wrench, if necessary, and then get to the washer. Make sure you also unplug the washer. There are only two Phillips head screws to remove to get the vanity cover off of the back. For whatever reason my removal was a little bit difficult for this. There are some plastic clips that hold the front portion on of the vanity plate. These were very tight, and I was afraid I would break them, but eventually they came loose with gentle upward pulling. Once this was off, it was super easy to identify the part that needed replacement. There are two hose clamps that you just need a pair of pliers to squeeze in slide off the hose. Then you remove three additional Phillips head screws, and the other connections pop out on their own. The solenoid plugs are very simple to slide off, and it is really difficult to put them on any other way. If you need to, you can take a few photos of the installation. Once you have the old one out, hook up the hoses first, and slide the hose clamps back to their original position. Once you have the two black hoses back on, reposition the new valve body, and slide the additional three prongs into the inlet soap dispenser. Make sure that the fit is snug. Don’t over push, the parts are plastic. Once this is done, reinsert, the three Phillips screws into their holes. Then you can reconnect the solenoids. At this point the replacement is done, and all you have to do is replace the vanity cover. Take time to ensure that you’ve done this correctly. I left the vanity cover off and ran a test load of dirty clothes to make sure that there were no leaks. Once I assure, there were no leaks, I put the vanity cover back on and put the two screws on. This was a very easy fix. Again, just go slow removing the vanity plate so you do not crack or break the tines in the front.

After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem solved. Thanks for the fast service on my order.

I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.

raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turned on water supply valves. Done.

Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).

I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!