79573054411 Kenmore Refrigerator - Instructions

Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.

Had to buy the entire door mullion because the spring broke, wasn't happy. Got the new part very quickly and it was a new replacement part number. Somewhat tentative. Took it out of the box and looked it over. No spring! Groan! Thought I got the wrong part. Flipped the bottom hinge and it snapped open, no need for a spring! Two screws, disconnect the wire harness, throw away the old, get new, connect the wire harness, connect hinges, put in two screws! Super easy. Watch the video for some pointers along the way.

Found the broken spring; matched it with parts diagram. Googled for sources via part number. Selected this site because it had best deal - price, availability, shipping. Part arrived as predicted; installed it in 2 minutes. Job done. Door now works.

Installed easily. Left out old snap on new. Service over phone was excellent

You first have to measure length, width and depth to give to the person who answers your call, or else you may have to return your order. When I received my part, I easily placed it in our refrigerator.

REMOVED 3 SCREWS AND OUT IT CAME UNPLUG THE HARNES AT THE TOP YOUR NONE

Replaced shelf. Original shelf was the wrong size

When I sent an email about this and asked for a replacement, I was told I would need to send it back. I wrote back and reiterated that the glass was shattered and did they really want me to send it back. I again said just send me the replacement. Instead I got a response that sending it back was not necessary but that I would receive a refund and would need to reorder the part again. The part was $47.91 when I first purchased it. Now to reorder it is $54.98. I saved it in my shopping cart so I can shop around before purchasing this again. I am disgusted that I need to go through this again and now at a higher price. I have more parts to order but am reconsidering do so.

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

Watched a YouTube video on how to replace the door flipper (mullion). Very easy to unscrew the plate and disconnect the electrical circuit. Then gently slide up the flipper and replace with a new one.

Replaced drawer.

was easy watching youtube video of how to replace whole ice maker, was only 3 screws, remove from the door, a couple of screws hold it to the flat piece, route the wires around the unit, connect the plug as installing it in the door, position it, and tighten 3 screws, that easy

I looked at the picture I took. Used needle nose pliers and inserted one end. Unless the lady of the house is very strong, this should be handled by a man, because of the rigid spring. Once the spring was inserted into one side of the flap, I used the pliers to get the other end into the proper slot. Very easy, but the spring is very strong !!

The replacement basket for the left swing door went extremely smooth. The part was an exact fit and just required a little pressure while attaching the new replacement part.
highly recommend part select in doing a replacement for this part.
The schematic for the refrigerator is blurry and difficult to see on-line, so one a representative from parts select assisted me in finding the correct part.
two thumbs up!

Simply lifted old part up, removed. Took new part put in place and pushed downward as it firmly locked in place. Less than 1 min.