Sold individually. This part helps the flame to spread for even heat. Also protects your burner head from spills. The surface burner cap is located on the top of the burner head and is used in ranges ...
This part is the igniter/orifice mounting screw for your cooktop or range. It is approximately ½ an inch in length and is made of metal. The mounting screw connects the orifice to the cooktop. If the ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Edward
December 16, 2022
Only 1 of the ceramic burner electrodes will spark and ignite. The other 3 do not spark. I replaced the igniter harness without any improvement. I suspect I need to replace all 4 sparking electrodes, not only because 3 don't spark, but also because they're "gunked-up" with cooking carbon/grease. I tried cleaning them but no improvement. I'm unsure which part(s) to order. Please advise. Thank you.
For model number 79070502013
Hi Edward, thank you for reaching out. The problem appears to be with the Spark Ignitor and you may need to replace it, the part number is PS11728608. If that does not take care of the problem, we would recommend checking the Spark Ignition Switch Assembly, part number PS3409148. If you require assistance placing an order, please contact customer service. We hope that helps!
We need to replace the knob with the part attached to the knob. Are there replacements for those parts? It is a gas range.
For model number 79070502013
Hi Erin, thank you for reaching out. The knobs for your model are part number PS3408939. The parts that are attached to the knobs are the burner valves. The right front burner valve is part number PS2359010, and the rest of the 3 burner valves are having the same part number PS2359009. These replacement parts are sold individually. We hope this solves your problem!
All my display buttons slopped working it started out with the clock not keeping time it would start blinking and numerous attempts and now none of the buttons work
For model number 79070502013
Hello Mark, thank you for contacting us. Our research on your model shows that this issue could be caused by the control overlay, part number PS3408950. If that does not help, we recommend replacing the control board, part number PS1528270. If you require assistance to place an order, please contact customer service. We hope that helps!
I am an HVAC tech by trade so it wasn't difficult to diagnose problem with safety valve. The hard part was being without an oven for a week. Repair was simple and effective--oven works good as new. Shut off gas and unplugged oven. Removed floor of oven between broiler and bake section, used wrenches to disconnect gas line from safety valve in back of oven, used philipps head screwdriver to remove burner assembly and gas valve, reversed process to replace. Checked out operation--OK.
Turned off power, took back off stove removed old probe. I had to splice wires since new probe ends did not match up. the instructions were to splice the wires. I had the breaker off for about 3 hours. this is not in the instructions, but being a widow, I had to ask a few people why it would not come on after I connected the wires. After waiting, I turned the breaker on and my range came back on.
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.