This is a basket for washing flatware or silverware in your dishwasher. This part has been updated and may differ in appearance but will function the same as the original.
$81.34
In Stock
Order within the next 10 hrs and your part ships today!
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$9.83
In Stock
Order within the next 10 hrs and your part ships today!
Sold individually. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward.
$12.80
In Stock
Order within the next 10 hrs and your part ships today!
The rinse aid cap (sometimes referred to as the dispenser cap), covers the rinse aid dispenser on the dishwasher door. If your dishwasher will not dispense detergent, or it is leaking detergent, there...
$35.18
In Stock
Order within the next 10 hrs and your part ships today!
This is a door seal, but you may also know it as a door gasket and it is a part for your dishwasher. It provides a leak proof seal between the tub and the door of your appliance. You will need to repl...
$120.75
In Stock
Order within the next 10 hrs and your part ships today!
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve will open and close according to the desired amount of water needed.
$86.98
In Stock
Order within the next 10 hrs and your part ships today!
When replacing these fuses the wire harness must be replaced as well. It is located in the control panel. The harness is included with this part now.
$45.19
In Stock
Order within the next 10 hrs and your part ships today!
Questions And Answers for 66517052402
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cleo
August 11, 2023
I need the snap-in clip on side of upper rack that keeps the rack from dropping, or holds the rack in place.
For model number 66517052402
Hello Cleo, thank you for your inquiry. According to our research, the part you are looking for is the upper adjustable rack wheel, part number PS12347743. Glad to be of assistance!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put the new one in. That was the easy part (about 15 minutes). The entire job took 2-and-a-half hours, most of which was taken in disconnecting, cleaning up and reconnecting the dishwasher. It's much quieter now.
1. Remove torx screws around outer edge of inside of door. 2. Separate outer door panel from inner door panel. 3. Locate dispenser, and remove 6 hex nuts and 2 wires for solenoid. 4. Insert new dispenser and re-insert hex nuts. 5. Reinsert torx screws.