Models
>
62942975
62942975 Kenmore Cooktop - Overview
Models starting with 62942975
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Cooktop Downdraft Vent Grease Filter
PartSelect #: PS11757584
Manufacturer #: WPY706012
This grease filter is sixteen and a half inches long and nine inches wide. It is made of metal and is intended for use with downdraft ranges and cooktops.
$61.73
In Stock
Dual Radiant Element with Limiter
PartSelect #: PS11759488
Manufacturer #: W10823709
$287.17
In Stock
Surface Burner Switch
PartSelect #: PS12070671
Manufacturer #: W11088181
This is the replacement surface burner switch for your range. It measures approximately 1.5 inches by 1.5 inches, with a shaft that is approximately 1 inch long. The surface burner switch turns the su...
$107.00
In Stock
6 Inch Element with Limiter
PartSelect #: PS11764912
Manufacturer #: W10823704
This element can be used for the left front or right rear.
$342.28
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$6.91
In Stock
Motor Isolator
PartSelect #: PS11743903
Manufacturer #: WP71003558
This motor isolator is less than an inch long.
$10.38
In Stock
Air Inlet Grill
PartSelect #: PS2077285
Manufacturer #: 71001673
This part is located over top of the blower in the center of the stove top.
No Longer Available
Common Symptoms of models starting with 62942975
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Outer Ring of Dual Radiant Burner Does Not Come On
Undid two screws on underside of cook top, lifted and exposed underside. Transferred wires from the faulty burner to the new burner, one at a time, paying close attention to their respective position on the wiring posts/terminals. Undid two screws holding old burner and then mounted the new burner to underside of cook top. Was really simple to do. :)
Parts Used:
-
Christopher from Fredericksburg, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
42 of 60 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old switch had shorted and burned out
This was a range top. i removed the 12 hex machine scews holding on the top, then removed the two star screws holding the old switch. there were fore wire that had fitted on tabs. Hooked them to the new swtch and reassembeld. Easy repair since i could lift the unit out without disconnecting main cables. Replacement range would have been oveer $1000. Psrt was under $40 and delivered in a matter of days.
Parts Used:
-
Larry from Hampton Cove, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
37 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced heating element on flat surface stove top
I removed 4 screws and then lifted up the top it gave me access to the element I followed the direction that came with the element (very clear to follow) removed and installed the new element and it worked fine. Remember to unplug the stove if it is electric this is not in the instructions.
Parts Used:
-
dennis from assonet, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
34 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!