Models > 59661104100

59661104100 Amana Refrigerator - Overview

Sections of the 59661104100

[Viewing 10 of 10]
Keep searches simple, eg. "belt" or "pump".
Replacement Ice Maker – Part Number: D7824706Q
Replacement Ice Maker
★★★★★
★★★★★
(21)
PartSelect #: PS2121513
Manufacturer #: D7824706Q
NOTE: This replacement ice maker mechanism does NOT come with a cover, shut off arm, a wire harness, or the mounting hardware. Those must be ordered separately, or you can use the existing parts.
$159.98
  In Stock
Bimetal Defrost Thermostat – Part Number: WP10442411
Bimetal Defrost Thermostat
★★★★★
★★★★★
(6)
PartSelect #: PS11738231
Manufacturer #: WP10442411
This refrigerator defrost thermostat will cut out at 55 degrees Fahrenheit and kick back in when the temperature drops to 20 degrees Fahrenheit. The thermostat itself is a little over an inch long whi...
$51.69
  In Stock
Refrigerator Door Switch – Part Number: W11384469
Refrigerator Door Switch
★★★★★
★★★★★
(22)
PartSelect #: PS12728638
Manufacturer #: W11384469
Door switch turns the light off when you close the door.
$33.55
  In Stock
Run Capacitor – Part Number: WP65889-4
Run Capacitor
★★★★★
★★★★★
(2)
PartSelect #: PS11743364
Manufacturer #: WP65889-4
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.
$74.67
  In Stock
Condenser Fan Motor Kit – Part Number: 833697
Condenser Fan Motor Kit
★★★★★
★★★★★
(13)
PartSelect #: PS395284
Manufacturer #: 833697
This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.
$64.14
  In Stock
Defrost Timer Kit - 120V 60Hz – Part Number: R0131577
Defrost Timer Kit - 120V 60Hz
★★★★★
★★★★★
(8)
PartSelect #: PS2167006
Manufacturer #: R0131577
The timer will shut off the cooling system of the refrigerator and the defrost heater will turn on.
$53.84
  In Stock
Freezer Door Gasket – Part Number: WP12550116Q
Freezer Door Gasket
★★★★★
★★★★★
(5)
PartSelect #: PS11738527
Manufacturer #: WP12550116Q
This freezer door gasket is white and made of rubber. It measures approximately 23-3/4 inches wide by thirty-one and a half inches long.
$130.09
  In Stock
Door Switch – Part Number: W11396033
Door Switch
★★★★★
★★★★★
(8)
PartSelect #: PS12731166
Manufacturer #: W11396033
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
$33.55
  In Stock
Water Fill Cup and Bearing – Part Number: WP628356
Water Fill Cup and Bearing
★★★★★
★★★★★
(1)
PartSelect #: PS11743318
Manufacturer #: WP628356
This icemaker water inlet cup is three inches long. It is all white in color and is made of plastic.
$47.21
  In Stock
Overload Relay Combination – Part Number: WP12555902
Overload Relay Combination
★★★★★
★★★★★
(4)
PartSelect #: PS11738533
Manufacturer #: WP12555902
This part is both the start relay and the overload. The start relay boosts the compressor, and then shuts off as soon as the motor gets up to speed and the overload provides extra protection against ...
$102.22
  In Stock
Crisper Drawer Cover Support Post – Part Number: 10461901
Crisper Drawer Cover Support Post
★★★★★
★★★★★
(1)
PartSelect #: PS1564421
Manufacturer #: 10461901
This part helps support the crisper drawer lid.
$43.26
  In Stock
Screw – Part Number: WPW10348409
Screw
PartSelect #: PS11753384
Manufacturer #: WPW10348409
Sold individually.
$9.36
  In Stock

Questions And Answers for 59661104100

Be the first to ask our experts a question about this model!

Common Symptoms of the 59661104100

[Viewing 22 of 22]
Ice maker not making ice
Fixed by
these parts
Show All
Light not working
Fixed by
these parts
Show All
Leaking
Fixed by
these parts
Show All
Fridge too warm
Fixed by
these parts
Show All
Freezer section too warm
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Door Sweating
Fixed by
these parts
Show All
Freezer not defrosting
Fixed by
these parts
Show All
Ice maker won’t dispense ice
Fixed by
these parts
Show All
Fridge runs too long
Fixed by
these parts
Show All
Fridge and Freezer are too warm
Fixed by
these parts
Show All
Frost buildup
Fixed by
these parts
Show All
Ice maker dispenses too much ice
Fixed by
these parts
Show All
Clicking sound
Fixed by
these parts
Show All
Too warm
Fixed by
these parts
Show All
Freezer too cold
Fixed by
these parts
Show All
Fridge too cold
Fixed by
these parts
Show All
Door won’t open or close
Fixed by
these parts
Show All
Ice maker dispenses too little ice
Fixed by
these parts
Show All
Not dispensing water
Fixed by
these parts
Show All
Won’t start
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of connection held the other two attachment points along the long edge of the icemaker. I did not have repair manual or useful drawing but looked @ PartsDirect pic of side brackets & used a small mirror to confirm that mine were also some sort of "snap in" attachment.
Remove icemaker unit by pushing upward and outward on the unit. I takes a good bit of pressure and will pop loose, but be careful not to break attachment bracket from freezer wall.
Scavenge shut off bar and wiring harness from old icemaker once you have it out & attach to new one before installing it back in freezer.
Again, you might find a mirror useful to align those pesky snap-in brackets with the new unit.
Since you probably kept your freezer running while waiting for the part, the plastic snap-ins will be cold and brittle. I warmed them up first by applying a dampened cloth heated in the microwave to make them a little more pliable.
A good push of the new unit towards the snap-ins along with some upward force will get it stable.
Reattach the metal screw in bracket & connect the wiring harness to rear plug... and don't forget to plug the whole thing back in.
It will take awhile for the first batch of cubes dump as the timer may need to cycle completely around to get to the fill cycle... be patient.
Dump the first couple of batches of cubes just to make sure you're free of any residue.
Parts Used:
Replacement Ice Maker
  • Bernie from Diamond Bar, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
786 of 851 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflowed ice maker turnning ice bucket into solid mass of ice
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: one of the three screws that hold the ice maker to the refrigerator wall is hidden behind the large (black) end of the ice maker and is difficult to access. Before trying to replace the ice maker, make sure you have the physical dexterity to remove that screw. Second problem: it is not apparent how to remove the wire harness that plugs into the ice maker assembly. BEFORE you can remove the wire harness, you MUST remove the large white cap that covers the black end of the ice maker assembly and then push in a retaining tab to release the wire harness. If you don't do this, the wire harness will not release. Other than those two problems, it was relatively easy to remove three screws, unplug the wire harness, transfer three small, metal parts from the old ice maker to the new, plug in the new wire harness, mount the ice maker assembly so that the water tube is in the proper position, and then re-install the three screws. The ice maker works fine now. (P.S. I was told by an expert that the real problem might be a malfunctioning fill valve. I would have replaced the fill valve if replacing the ice maker assembly had not fixed the problem.)
Parts Used:
Replacement Ice Maker
  • Harry from Grand Ledge, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
263 of 347 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sometimes the condenser fan would start causing the refrigerator to overheat.
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire about two inches from the fan.
Cut and strip the new wire. I cut the new wire in half (about 6 inches.) Connect the two wires, twist and used 2 wire nuts. Tie wrap the wire to the wire harness. Mount the new fan (three screws)
Screw the back panel back on.
Mount the new
Parts Used:
Condenser Fan Motor Kit
  • Tom from Franklin, WI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
172 of 189 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!