Models
>
2514
2514 Cooktop - Overview
Models starting with 2514
Click on the best match to narrow your results.
Exact Part matches for your search term
[Viewing 1 of 1]
GUARNIZ.FIBRA FLANG.R.CIRC.27
This part number matches the current model number 2514
PartSelect #: PS17234002
Manufacturer #: 2514
No Longer Available
Keep searches simple, eg. "belt" or "pump".
Delta Frame Surface Unit - 8 Inch
PartSelect #: PS11757481
Manufacturer #: WPY04100166
This 8 inch surface burner with reinforced delta frame carries 2100 watts and 240 volts. It has five turns and is compatible with many electric ranges. Its center medallion is all black in color.
$56.86
In Stock
Delta Frame Surface Unit - 6 Inch
PartSelect #: PS11757480
Manufacturer #: WPY04100165
This 6 inch surface burner with reinforced delta frame carries 1250 watts and 240 volts. It has four turns and is compatible with many electric ranges. Its center medallion is all black in color.
$64.85
In Stock
Chrome Trim Ring - 8 Inch
PartSelect #: PS11757588
Manufacturer #: WPY707453
This trim ring is used with many electric ranges. It is a chrome trim ring that is intended for use with eight inch surface burner elements.
$82.05
In Stock
Chrome Trim Ring - 6 Inch
PartSelect #: PS11757589
Manufacturer #: WPY707454
This trim ring is intended for use with many electric ranges. It is a chrome trim ring that is used with six inch surface burner elements. Notes The matching eight inch chrome trim ring is available w...
$68.72
In Stock
Exhaust Vent Blower Wheel
PartSelect #: PS11757592
Manufacturer #: WPY707985
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
$118.15
In Stock
Blower Motor
PartSelect #: PS2076843
Manufacturer #: 707704K
This part is used with down-draft models. It helps draw the steam and odors through the vent when the fan switch is activated.
$464.07
In Stock
Common Symptoms of models starting with 2514
[Viewing 2 of 2]Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bad element control switch
1. Turn off power to range at circuit breaker
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new switch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power
2. Remove grate
3 Remove control knobs
4, Remove two screws holding control panel
5. With wrench, remove locking nuts from control switches
6. Lift panel, exposing switches
7. With new switch in hand, unattach old switch one terminal at a time, attaching new switch exactly as old switch, terminal by terminal.
8. Replace everything in reverse order
9.Turn on power
Parts Used:
-
Richard from Beverly Hills, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Wrench set
11 of 15 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor bearing failure after 34 years.
Important: Down load the helpful assembly diagram for the fan motor and study it for a few minutes. It's very straight forward. Also a good idea is to remove the bottom panel which comes off easy before starting.
My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work bench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.
Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.
Wife is happy...
Wade
My only problem was removing the existing blower/fan wheel without damaging it once I had the assembly on the work bench. It was rusted on tight and managed to remove after a few tries using penetrating oil. The wheel is in stock and I'd suggest buying a new one along with the new motor if I had to do the job again.
Bottom line; the fan motor fit perfect but did have to re-use part of the old existing electric pig tail because the motor does not come with the factory type motor terminal connectors. By using three twist on wire connectors was back in business. The down draft vent works like new.
Wife is happy...
Wade
Parts Used:
-
Wade from CARMINE, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old burners, burning very uneven!
-
Robert from Falls City, NE
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!