Hammer Drill Parts

Find Your Part

Model number locator Need help finding your model number?
  • Search your model number to find:
  • Genuine OEM parts guaranteed to fit
  • Free manuals and guides
  • Repair instructions and videos
Original Equipment Manufacturer

Why Genuine OEM Matters
Shop By Brand

Popular Hammer Drill Parts

Your Price
$23.95
  In Stock
Hammer Drill Power Cord
PartSelect Number PS10153834
Manufacturer Part Number 664064-4
Length 8 Foot Length: 6' Gauge: 18 Wires: 2 Type: Bare Wire This power supply cord is a genuine OEM sourced replacement part. It is specially made to supply power from a standard outlet to Makita power tools. A cracked or damaged cord should be replaced before continuing to use the tool. This rubber insulated cord is sold individually. It comes with a rubber sleeve grommet that is not sold separately. Replacing this power supply cord you will need a screwdriver. • Remove the housing screws • Remove the the housing • Disconnect the old cord wires • Remove the old power cord • Secure the new cord in place • Connect the wires • Reassemble and test the new cord
Your Price
$6.95
  Special Order
Hammer Drill Cord Guard
PartSelect Number PS10153918
Manufacturer Part Number 682502-4
This cord guard is a genuine Makita replacement part, and it is a direct replacement for a damaged or missing cord guard. Power tool cords undergo a lot of stress, and these cord guards help to alleviate some of that stress at the weakest point--right where the cord enters the tool. Over time cord guards will deteriorate and eventually require replacement. Keeping a strong cord guard on your tool will help will cord life. This cord guard is compatible with the tools listed below, but it is not guaranteed to fit any other power tools.
Your Price
$11.95
  In Stock
Hammer Drill Ball Bearing 6000ddw
PartSelect Number PS10141492
Manufacturer Part Number 210059-1
This authentic replacement part which is specially designed for use with Makita power tools. Ball bearings are used to reduce friction between rotating parts, over time components may begin to wear out and fail eventually requiring a replacement. Please note this high-quality ball bearing is made of durable metal and it is sold individually.
Your Price
$5.95
  In Stock
Hammer Drill O-ring
PartSelect Number PS10142024
Manufacturer Part Number 213962-5
This replacement o-ring is specially designed for use with Makita rotary hammers. It is an authentic manufacturer sourced item that is used to provide a seal for the striker and the piston. For correct location please make sure to check appropriate diagrams of your unit. Over time seals and o-rings tend to shrink, become brittle and crack eventually requiring replacement. Please note one durable rubber o-ring is included per order. Replacing this item you would need hex key which is also known as an allen wrench to complete the repair.
Your Price
$5.95
  Special Order
Hammer Drill O Ring 28
PartSelect Number PS10141868
Manufacturer Part Number 213415-4
This is a genuine replacement part designed for use with Makita power tools. This o-ring provides an air-tight seal for the connected parts. Please make sure to check appropriate diagrams for location and use of this item. Over time o-rings will shrink, become brittle and crack allowing for air leaks. At that time they should be replaced. It is made out of rubber and it is sold individually.
Your Price
$26.95
  Special Order
Hammer Drill Brush Holder Unit
PartSelect Number PS10153125
Manufacturer Part Number 632D00-2
This replacement brush holder unit is a high quality item that is supplied by original equipment manufacturer for use with Makita demolition hammers. Its purpose is to secure carbon brushes around the armature to maintain stable contact. This item is a complete assembly which includes the plastic ring, two metal brush holder with attached lead wires, please note the carbon brushes themselves are sold separately. Keep in mind this brush holder unit is sold individually.
Your Price
$15.95
  Special Order
Hammer Drill Ball Bearing
PartSelect Number PS10141520
Manufacturer Part Number 211031-6
Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating parts in your tool. The balls or rollers bear the load and spin, distributing the weight evenly, while the minimal contact area of the balls reduces friction. This reduces wear on the tool, allowing it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.
Your Price
$5.95
  Special Order
Hammer Drill Compression Spring 3
PartSelect Number PS10143081
Manufacturer Part Number 231403-9
This is an authentic OEM part. The Makita compression spring 3 is constructed of metal, and is compatible with the HK1810 Scraper. This part is secured between the steel ball and tool holder, helping the device to hold specific scraping tools. This part is sold individually. A wrench is helpful in the removal and replacement.
Your Price
$31.95
  Special Order
Hammer Drill Variable Switch
PartSelect Number PS10153474
Manufacturer Part Number 650208-2
This Trigger type VAR switch has 4 internal terminals and a locking mechanism. This genuine Makita replacement part is sold individually. Switches are commonly replaced parts in power tools. A switch handles on/off and variable speed functions. They also have a role in electric breaking; they can momentarily reverse electrical polarity. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. Some common signs of a broken or failing switch are: • The tool has completely stopped functioning • it will not turn on. • The tool operates intermittently, requiring multiple tries to turn on, until eventually it won't turn on at all. • The variable speed function and electric braking aren't working properly.
Your Price
$5.95
  Special Order
Hammer Drill Flat Washer 7
PartSelect Number PS10144379
Manufacturer Part Number 253823-7
This is an authentic replacement part manufactured for Makita products. This metal washer has many applications usually used as a spacer for bearings. This washer is sold individually, please see model diagram for part location or additional parts.

Hammer Drill Brands

Popular Hammer Drill Models

Below are the most popular Hammer Drill models we have. Enter your model number in the search box to find your model.

Need Help Finding Your Model Number?
View More