This agitator cam kit contains an almost three inch white retainer and four agitator dog ears. This kit is used to move the upper agitator and it connects the base of the agitator with the agitator top (mover).
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer Dryer Combo, Washer.
This part works with the following products:
Kenmore, Whirlpool, Maytag, Crosley.
Part# 285751 replaces these:
AP3094521, 2837, 285751, 3351019, 387092, 3947410
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Andre A - November 20, 2022
Verified Purchase
Agitator parts replaced
The part was an exact fit and took me 20 minutes to swap out old for new. Washer agitator works like new.
★★★★★
★★★★★
Iqbal P - October 22, 2019
Verified Purchase
Awesome customer service
I needed this cam kit and I called this company for the part, the receptionist that I dealt with was super professional, answered all my questions and got me the part I required for my washer unit. I even received the part the next day before I got home from work and I ordered this part at 4pm the previous day. Just awesome service.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 25 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Top half of agitator didn't agitate
First I removed the fabric softener container and set it aside. Below that, there is a plastic cover with a rubber gasket that distributes the fabric softener. I also just pulled that out and set it aside. Below that was an 11mm bolt that attached the upper and lower agitator to the drive mechanisim. The lower agitator is attached directly to the shaft and that was working properly so I knew it was't a motor or drive issue. Until it broke, the top half of the agitator sat still for a second, then it turned clockwise with the lower agitator. This helped push the clothes down to the lower part to be circulated throughout the wash cycle. Well, now the upper agitator just sat there, like it wasn't attached to anything at all. Below the aforementioned plastic cover with the rubber gasket, I found a part that had 4 plastic "teeth" that moved in and out, releasing and grabbing the inside of the upper agitator, respectively. Over time, these teeth wore down and stopped "grabbing" the ridges on the inner part of the upper agitator, causing it to stop turning with the lower agitator. I removed the 11mm bolt and tried to seperate the upper agitator from the lower agitator to replace the teeth. This part was kind of tough to get out because the plastic clips that held it in were deformed. I just had to pull hard and eventually it came apart. In the process, I broke two of the clips. I wasn't really concerned because the 11mm bolt holds everything in place anyway. After that I just swapped out the worn teeth with the new ones. I put it back together in the opposide order I took it apart and viola....good as new. And it only cost me $15 bucks.
Other Parts Used:
Nathaniel from Kennesaw, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
73 of 81 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
machine would not spin
Disconnect electrical, took out agttator, tipped machine againest the wall. On hooked the two hoses on pump, removed three bolts pulled complete assembley out removed worn parts and installed new parts and reassembled. Works like new,
Popped the agitator cap with a flathead screwdriver. Removed the dust cap, tearing the o-ring in the process. Removed the bolt that holds the agitator in place, removed the whole agitator. Pulled the top portion of the agitator off, removed the dog housing and all pieces of the broken dog pieces. Replaced them, and put it all back together in reverse order. Pretty straight forward repair. Works great!
Motor was working and rotating lower portion of agitator, but the top was not spinning.
1. Remove the fabric softener receptacle
2. Remove the plastic dome shaped separator with a rubber o-ring around it (directly beneath fabris softener receptacle)
3. There is an 11mm bolt right in the center. Use socket wrench to remove bolt.
4. Remove agitator from washign machine.
5. Separate top half of agitator from bottom half (this was the most difficult part for me; unlike others who have described this repair, mine would not simply pull apart; I spent quite a while trying to pry up the white plastic clips extending from the bottom piece through the clear plastic piece that covers the "dog teeth" that make the top piece agitate)
6. Once apart, replace worn "dog teeth" with new dog teeth.
7. Put back together in reverse order.
Other Parts Used:
Brad from Boise, ID
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set
22 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper agitator did not rotate
Removed the rinse dispenser from Agitator. Unbolted and removed agitator from machine. Directions said remove upper agitator by pulling apart. Had to brace bottom with both feet, and lift straight up. Came off. Replaced 4 cogs, re=assembled and re-installed.
Other Parts Used:
Robert from Brooksville, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
11 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
aggitator stripped, not turning
removed the cap and unscrewed locking fitting. Removed aggitator dogs and replaced with new and reassembled.
pop the cap off the top of center agitator unit, remove one 11mm bolt and remove unit from washer. take apart, remove & replace broken dogs and reassemble. I actually bought the wrong kit, my cam is much longer but since the problem was caused by the broken dogs it did not matter.
Other Parts Used:
Brian from Staunton, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator gears stripped out
First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great
Other Parts Used:
Nathan from Bellingham, MA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitor cams wore out
I ordered a new part based on the exact model number and was sent the wrong part. Fortunately the cam dogs were the same size so I was able to re-use the original housing and throw the new one away.
Other Parts Used:
Merlin from Scott, LA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer machine wouldn't turn
It was a really simple thing to do. Make sure to buy the agitator cam kit (a little piece broke when I was taking it apart). Take off the cover and then the nut that is underneath. Replace the agitator cam and that's it!!! Usually those agitators dog ears wear down with time so if the agitator assembly is not turning, check this first.
Other Parts Used:
Isaac from Bridgeport, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
September 21, 2023
With the washer door open AND door safety switch depressed. The spin cycle will only work when I press down on the agitator. If not depressed the agitator will only hit and miss.
For model number LTG6234DQ1
Hello Bob, thank you for contacting us.Based on the understanding of the issue, we would recommend checking the agitator bolt, part number PS11741866, to fix the issue. We hope this helps!
This is the cam kit that I have and I took it apart to clean but when putting it back together the agitator dogs falls out of place because theirs nothing holding them in the cam is there something I'm missing?
For model number Ywet3300xq2
Hello Dylan, thank you for reaching out. According to our research, the issue is most probably with the agitator cam. It holds the agitator dogs. We would recommend replacing the agitator repair kit, part number PS334624, to solve the problem. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Our scratch-free, streak-free formula removes fingerprints, smudges, grease, dirt and oil, while protecting and polishing to repel dust and dirt. Use on all stainless steel appliance brands and surfaces. Stainless Steel ...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS334624
Manufacturer Part Number: 285751