11081422510 Kenmore Washer Dryer Combo - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator Directional Cogs – Part Number: 80040
$6.55
In Stock
Agitator Directional Cogs
★★★★★
★★★★★
(200)
Part #80040
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
Door Catch Kit – Part Number: 279570
$10.58
In Stock
Door Catch Kit
★★★★★
★★★★★
(87)
Part #279570
This kit contains two door strikes, and three door catches to service dryer doors that have one or two catches.
Rear Drum Support Roller Kit – Part Number: 349241T
$29.23
In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(63)
Part #349241T
This dryer drum roller kit is designed to restore smooth and quiet operation in a wide range of dryer models. It includes two drum rollers, four tri-rings, and one to two retaining washers, providing all necessary components for a complete replacement. The rollers support the drum as it rotates, and worn or damaged rollers can cause excessive noise, poor tumbling performance, or even leave marks on clothing. Replacing these components can resolve issues such as rumbling, squealing, or grinding sounds during operation. Compatible with many units from Whirlpool, Kenmore, Sears, and other brands, this kit offers a reliable solution for maintaining optimal dryer performance.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Agitator Bolt – Part Number: WP358237
$15.56
In Stock
Agitator Bolt
★★★★★
★★★★★
(5)
Part #WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Dryer Lint Filter and Cover – Part Number: W10828351
$77.53
In Stock
Dryer Lint Filter and Cover
★★★★★
★★★★★
(24)
Part #W10828351
This dryer lint filter and screen assembly is a genuine replacement part designed to trap lint and fibers during the drying cycle, helping to maintain airflow and prevent blockages in the vent system. Its kidney-shaped screen is constructed from durable steel and ABS plastic, housed within a cover that features four metal clips for secure installation. By capturing debris, it supports efficient drying times and reduces the risk of overheating or fire hazards. Compatible with various Whirlpool, Kenmore, and associated brand dryers, this OEM part replaces several previous versions and ensures a precise fit. Regular inspection and replacement of the lint filter are recommended to maintain optimal dryer performance.
Washer Inner Cap Seal – Part Number: WPW10072840
$15.41
In Stock
Washer Inner Cap Seal
★★★★★
★★★★★
(2)
Part #WPW10072840
Also known as an O-Ring. This black o-ring seal is three inches in diameter.
Centerpost Gasket – Part Number: W10814296
$12.01
In Stock
Centerpost Gasket
★★★★★
★★★★★
(6)
Part #W10814296
This main outer tub seal is a critical component that prevents water from leaking at the bottom of the tub during operation. Measuring approximately 2 inches in diameter, it is constructed from durable black plastic for long-lasting performance. Proper installation requires disconnecting power, drain hose, and inlet hose, followed by removing the outer cabinet and the entire tub assembly. Inspect the seal for cracks or wear during maintenance to avoid leaks and ensure optimal washer performance.
Heating Element Connection Wire Kit – Part Number: 279457
$13.97
In Stock
Heating Element Connection Wire Kit
★★★★★
★★★★★
(4)
Part #279457
This kit is used for electric clothes dryers, and it comes with a yellow wire nut.
Washer Washer – Part Number: WP3949550
$17.26
In Stock
Washer Washer
★★★★★
★★★★★
(1)
Part #WP3949550
This part goes on the agitator retaining bolt.
Door Catch – Part Number: WP3389441
$14.95
In Stock
Door Catch
★★★★★
★★★★★
(8)
Part #WP3389441
This white female door catch is attached to the dryer door.
Air Conditioner Cover Screw – Part Number: WP308685
$10.95
In Stock
Air Conditioner Cover Screw
Part #WP308685
Sold individually.

Questions And Answers for 11081422510

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Faye - For model number 11081422510
September 16, 2025
On this stackable, the dryer works normally, but the washier will not start.
Chris Boyle Profile
Hello Faye, thank you for contacting us. Check the lid switch, part number PS1482372. If the lid switch is faulty, the washer will not start or spin. If the lid switch is working, you will need to check the drive motor, part number PS11754879. The motor might be faulty, not letting the washer start. We hope this information helps!
$73.00
Special Order
Lid Switch with Wire Harness
$431.31
On Order
Drive Motor
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
Joseph - For model number 110.81422510
May 13, 2026
Will not proceed to rinse cycle. Timer stops and hear buzzing noise on all cycles. Any ideas
Chris Boyle Profile
Hello Joseph, thank you for contacting us. If your appliance stops at the rinse cycle, stalls the timer, and emits a loud buzzing or humming noise, the issue could be with the motor capacitor, part number PS11746660. The capacitor loses its ability to store and release the electrical charge needed to give the heavy drive motor an initial high-torque turning boost. Without this electrical kick-start, the motor remains completely stationary when the rinse cycle demands a spin, converting the incoming current into a loud humming noise. You may need to replace it. We hope this sorts out your problem!
$81.45
In Stock
Washer Capacitor Motor Start
Was this helpful?
Thank you for voting!
Matthew - For model number 11081422510
February 4, 2024
The washer operates normally, however, the dryer doesn't start. The door switch is functioning normally. What would be the next part to check?
Chris Boyle Profile
Hello Matthew, thank you for getting in touch. Based on our understanding of the issue, we would suggest checking the timer, part number PS11741711, to solve the problem. We hope that helps!
$428.00
Special Order
Timer
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the 11081422510

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer wouldn't agitate
956 of 1058 people found this instruction helpful.
  • mike from Kent, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Was this helpful?
Thank you for voting!
Door Catch part had fallen out,/ was missing
676 of 740 people found this instruction helpful.
  • Terri from Saint Augustine, FL
  • Really Easy
  • Less than 15 mins
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
Was this helpful?
Thank you for voting!
top half of agitator did not move during wash cycle
288 of 337 people found this instruction helpful.
  • dennis from new stanton, PA
  • Really Easy
  • Less than 15 mins
  • Socket set
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of o ld cogs remove and replace with new, reassemble
Was this helpful?
Thank you for voting!