11080754000 Kenmore Washer Dryer Combo - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator Directional Cogs – Part Number: 80040
$6.55
In Stock
Agitator Directional Cogs
★★★★★
★★★★★
(200)
Part #80040
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
Direct Drive Motor Coupling – Part Number: 285753A
$27.20
In Stock
Direct Drive Motor Coupling
★★★★★
★★★★★
(95)
Part #285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission and the motor shaft. It attaches to the direct-drive transmission and the motor shaft. If this part is defective it will affect the agitator in your washer because of its direct connection with the motor. Your washer may not agitate, spin slowly, or not spin at all. The coupling must be replaced when there is no longer a consistent connection between the transmission and the motor shaft. The coupling can wear over time because of its location between two major parts of the dryer. It is subject to material fatigue over time from normal use, or breakage caused by frequent overloading. The part measures approximately 2 inches in diameter, and is constructed of plastic and metal. This model comes in black/white.
Door Catch Kit – Part Number: 279570
$10.58
In Stock
Door Catch Kit
★★★★★
★★★★★
(87)
Part #279570
This kit contains two door strikes, and three door catches to service dryer doors that have one or two catches.
Washer Direct Drive Water Pump – Part Number: WP3363394
$60.45
In Stock
Washer Direct Drive Water Pump
★★★★★
★★★★★
(61)
Part #WP3363394
This pump is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.
Washer Clutch Assembly – Part Number: 285785
$52.75
In Stock
Washer Clutch Assembly
★★★★★
★★★★★
(57)
Part #285785
A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the blue spring (1.24") replaces the black spring (1.46").
Rear Drum Support Roller Kit – Part Number: 349241T
$29.23
In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(63)
Part #349241T
This dryer drum roller kit is designed to restore smooth and quiet operation in a wide range of dryer models. It includes two drum rollers, four tri-rings, and one to two retaining washers, providing all necessary components for a complete replacement. The rollers support the drum as it rotates, and worn or damaged rollers can cause excessive noise, poor tumbling performance, or even leave marks on clothing. Replacing these components can resolve issues such as rumbling, squealing, or grinding sounds during operation. Compatible with many units from Whirlpool, Kenmore, Sears, and other brands, this kit offers a reliable solution for maintaining optimal dryer performance.
Water Inlet Valve with Mounting Bracket – Part Number: 285805
$46.79
In Stock
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
(41)
Part #285805
The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Washer Tub Spring – Part Number: WPW10250667
$12.95
In Stock
Washer Tub Spring
★★★★★
★★★★★
(23)
Part #WPW10250667
This part is used to balance the tub during spin cycle. Sold individually.
Agitator Bolt – Part Number: WP358237
$15.56
In Stock
Agitator Bolt
★★★★★
★★★★★
(5)
Part #WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
Dryer Lint Filter and Cover – Part Number: W10828351
$77.53
In Stock
Dryer Lint Filter and Cover
★★★★★
★★★★★
(24)
Part #W10828351
This dryer lint filter and screen assembly is a genuine replacement part designed to trap lint and fibers during the drying cycle, helping to maintain airflow and prevent blockages in the vent system. Its kidney-shaped screen is constructed from durable steel and ABS plastic, housed within a cover that features four metal clips for secure installation. By capturing debris, it supports efficient drying times and reduces the risk of overheating or fire hazards. Compatible with various Whirlpool, Kenmore, and associated brand dryers, this OEM part replaces several previous versions and ensures a precise fit. Regular inspection and replacement of the lint filter are recommended to maintain optimal dryer performance.
Dryer Idler Pulley Assembly – Part Number: WP691366
$24.19
In Stock
Dryer Idler Pulley Assembly
★★★★★
★★★★★
(2)
Part #WP691366
The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.

Common Symptoms of the 11080754000

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No movement from Basket & agitator
1124 of 1228 people found this instruction helpful.
  • Jeff from Wayne, NJ
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pum p.
The motor comes off next. Unplug the electrical connector from the motor and two wires from the capacitor. Remove the two screws holding the clamps in place and then pop off the two clamps. You will need to hold up the motor with one hand while you remove the clamps or it will fall to the floor once the clamps are removed.
One piece of the coupling assemble will be attached to the motor and the other will be attached to the gearcase drive shaft. If you want to clean up the mess created by the shredded rubber center piece of the coupling assembly you will have to take off the motor mounting plate. It is held on by two bolts and removing it makes installing the coupling easier but probably not necessary.
Push the back half of the coupling on to the gearcase drive shaft until the shaft is flush with the face of the coupling. Install the new rubber center piece on to the coupling then re-install the motor mounting plate. Install the other half of the coupling on to the motor shaft and lift the motor up to the coupling. You have to rotate the motor shaft by spinning the fan blades until the coupling lines up so you can slide it into the other half of the coupling. Then just reattach the motor, connectors and water pump in the reverse order of disassembly.
Was this helpful?
Thank you for voting!
washer wouldn't agitate
956 of 1058 people found this instruction helpful.
  • mike from Kent, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Was this helpful?
Thank you for voting!
Door Catch part had fallen out,/ was missing
676 of 740 people found this instruction helpful.
  • Terri from Saint Augustine, FL
  • Really Easy
  • Less than 15 mins
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.
Was this helpful?
Thank you for voting!