WM2016CW (01) LG Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer would not start, but if you disconnect it and plugged it in it started without pushing start button
1 person
found this instruction helpful.
-
DENNIS from EAST MEADOW, NY
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time.
However, after replacing the door lock it was obvious that this was not the problem. I had to remove the n ... Read more ew part and replace the old one.
For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.
However, after replacing the door lock it was obvious that this was not the problem. I had to remove the n ... Read more ew part and replace the old one.
For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.
Read less
Was this helpful?
Thank you for voting!
Error code DE
1 person
found this instruction helpful.
-
Mark from SOQUEL, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly!
I am a 63 woman and found this easy to do, with help from you tube guy.
I am a 63 woman and found this easy to do, with help from you tube guy.
Was this helpful?
Thank you for voting!
Drain water was not being fully pumped out, leaving foul water in the tub and wet clothes smelling like sewage.
1 person
found this instruction helpful.
-
Myles from Kingston, NH
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the
... Read more
process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!
Read less
Was this helpful?
Thank you for voting!
Both were dripping water .
1 person
found this instruction helpful.
-
Darrell from HENDERSONVLLE, NC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Watched video on U-Tube , unplug power cord, turn off water, take top off washing machine, remove water hoses, unscrew parts, remove hoses with pliers, install replacement parts, put all back together. Does not leak any more !
Other Parts Used:
Was this helpful?
Thank you for voting!
Hot water inlet had leak, kept filling washer, when offw
1 person
found this instruction helpful.
-
Rudy from SAN DIEGO, CA
- Really Easy
- 30 - 60 mins
When to utube typed in my problem, very easy fix
Was this helpful?
Thank you for voting!
Error code "EO", Drain Pump not working
1 of 2 people
found this instruction helpful.
-
Stephen from DEMING, NM
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the video on the PartSelect web site for this repair and it went just fine. I also replaced the drain hose while I had everything apart. Thank you PartSelect, same day shipping. Arrived within 3 day's and your video was spot on.
Was this helpful?
Thank you for voting!
Pump stopped working
1 of 2 people
found this instruction helpful.
-
Martin from Pie Town, NM
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Followed the video instructions provided.
Was this helpful?
Thank you for voting!
WASHER WOULD NOT EMPTY WATER DURING RINSE
1 of 3 people
found this instruction helpful.
-
michael from GRANTS PASS, OR
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS
Other Parts Used:
Was this helpful?
Thank you for voting!
The hot water inlet valve was leaking at the seal between the valve and cellinoid.
0 of 1 people
found this instruction helpful.
-
john from pearl river, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.
Was this helpful?
Thank you for voting!
watereaking from the hot inlet valve,and the clamp and hose got corroded from the bleach holding compartment
0 of 1 people
found this instruction helpful.
-
Jennifer from Hagerstown, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
removed two screws from back of front load washer slid the top back two inches and pulled up removing the top.Turned the water off at the shut off . Used the pliers to remove the clamps on the hose to replace. Put the new hose on with new clamps. Un screwed the two screws holding the inlet valve and removed the hose and clamp. Put the new
... Read more
part in and put the hose and clamp back on then put the two screws back that hold the inlet valve.Total time to unpack the parts and install 7 minutes. All I did was google it on youtube and order the parts from this site which only took 2 days and tah dah .
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
slow water leak
0 of 1 people
found this instruction helpful.
-
mark from pleasant prairie, WI
- Really Easy
- Less than 15 mins
-
Screw drivers
Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may
... Read more
need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.
Read less
Was this helpful?
Thank you for voting!
Hot Water Inlet valve (solinoid valve leaking)
-
MARVIN from MARYVILLE, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arri
... Read more
ved 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy
Read less
Was this helpful?
Thank you for voting!
The washer kept displaying "tE" error and the machine would stop.
-
William from Edgewood, MD
- Really Easy
- Less than 15 mins
First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holdi
... Read more
ng the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.
Read less
Was this helpful?
Thank you for voting!
Leaking water on my Hardwood floor
-
William from Campbellsville, KY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.
Was this helpful?
Thank you for voting!
the water inlet was leaking
-
gerald from wis dells, WI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done
Was this helpful?
Thank you for voting!