WM2016CW (01) LG Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
WASHER WOULD NOT FUNCTION BECAUSE DOOR LOCK ACTUATOR (ORIGINAL) FAILED.
2 of 2 people
found this instruction helpful.
-
BRAD from AUBURN, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.
Was this helpful?
Thank you for voting!
Drain pump inoperable
2 of 2 people
found this instruction helpful.
-
Gregory from PITTSBURGH, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Was this helpful?
Thank you for voting!
Water wouldn't drain
2 of 2 people
found this instruction helpful.
-
lawrence from DOBBS FERRY, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine a
... Read more
nd checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Read less
Was this helpful?
Thank you for voting!
While replacing the tub support (spider) I chose to replace the gasket.
2 of 2 people
found this instruction helpful.
-
Robert from HYDE PARK, VT
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
The spider repair and the tub seal replacement are fairly complicated, and time-consuming, but manageable with patience. I viewed the youtube video that showed the process, which gave me confidence. It entails disassembling the machine and removing quite a few major pieces. Take care with the numerous screws and bolts, and be patient and
... Read more
you can be successful. Plan a lot of time for all the steps.
The hardest part is putting the door bellows back on.
The hardest part is putting the door bellows back on.
Read less
Was this helpful?
Thank you for voting!
Washer was putting water in tub when it was in the spin cycle
2 of 2 people
found this instruction helpful.
-
John from SOMERSET, KY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Unpluged -shut off water removed 2 screws on lid,removed lid took 2 screws out holding part on swapped the hoses out and pluged wires in.
Was this helpful?
Thank you for voting!
door lock malfunction
2 of 2 people
found this instruction helpful.
-
paul from DELAND, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar
... Read more
service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!
Read less
Was this helpful?
Thank you for voting!
Dishwasher would not fill
2 of 2 people
found this instruction helpful.
-
Jesse from CARNEGIE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this helpful?
Thank you for voting!
water failure
2 of 2 people
found this instruction helpful.
-
Harley from OKLAHOMA CITY, OK
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
followed video exactly and it worked perfectly
Was this helpful?
Thank you for voting!
Door Hinges, door lock assembly, frame door
2 of 2 people
found this instruction helpful.
-
Julius from WINNETKA, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Remove door assembly from the hinge, unscrewed screw from the panel. Leave couple screws to hold Hinges. Remove the rubber seal but stretching to spring out, not having rt tool (long nose plier). Remove rubber partially close to the hinge. Remove the Hinges and replaced it, then reverse putting together back. Use small screw driver to put
... Read more
spring tensioner back. Reinstall frame door to hinge, double check everything.
Read less
Was this helpful?
Thank you for voting!
Washing machine stopped purging water from drum to hose
2 of 2 people
found this instruction helpful.
-
Andria from EDINA, MN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went s ... Read more o I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went s ... Read more o I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
Read less
Was this helpful?
Thank you for voting!
No power to dishwasher. Confirmed that outlet had power coming out.
4 of 9 people
found this instruction helpful.
-
JOHN from FORT MYERS, FL
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upsi
... Read more
de down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.
Read less
Was this helpful?
Thank you for voting!
Te error
4 of 9 people
found this instruction helpful.
-
Luis from LEHIGH ACRES, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
Change the thermistor
Was this helpful?
Thank you for voting!
Washer would fail during cycle with IE error code
2 of 3 people
found this instruction helpful.
-
CJ from WENTZVILLE, MO
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
1. Unplugged electric chord from wall.
2. Pulled washer out into open area to get behind it.
3. Turned off hot and cold water faucets
4. Used channel locks to remove hot water and cold water hoses from back of washer. Dropping hose into a bucket to catch water from hose.
5. Removed screws (Phillips screw driver) hold ... Read more ing top to back of washer.
6. Pulled back on the top and lifted off washer.
7. Arranged new intake valve to mock location and setting of old intake valve.
8. Using Phillip screw driver, unscrewed old intake valve from back of washer.
9. Unconnected wiring from old intake valve. These were easily identified and not needed to mark left right center.
10. Using pliers, pinched hose clips and moved to middle of the hose. Did this for all 3 hoses.
11. Removed hose from old intake and connected to same location on new intake. Repeated for all 3 hoses.
12. Using pliers, pinched the clips and moved to the end of the new intake valve. Did the for all 3 hoses.
13. Using Phillips screw driver, screwed in the new intake valve where the old intake valve was located.
15. Inserted the wiring connects into new intake valve.
16. Reconnected water hoses back into washer machine (after inspecting and cleaning plastic strainer traps)
17. Turned on water faucets
18. Plugged in washer.
19. Ran an empty load for a cycle.
20. Did not fail.
21. Reattached top to washer. Laying down an inch from front and push forward to hear a click or lock. Then screwed in the 2 screws.
22. Pushed washer back into original location.
We have already performed 1/2 dozen loads.
2. Pulled washer out into open area to get behind it.
3. Turned off hot and cold water faucets
4. Used channel locks to remove hot water and cold water hoses from back of washer. Dropping hose into a bucket to catch water from hose.
5. Removed screws (Phillips screw driver) hold ... Read more ing top to back of washer.
6. Pulled back on the top and lifted off washer.
7. Arranged new intake valve to mock location and setting of old intake valve.
8. Using Phillip screw driver, unscrewed old intake valve from back of washer.
9. Unconnected wiring from old intake valve. These were easily identified and not needed to mark left right center.
10. Using pliers, pinched hose clips and moved to middle of the hose. Did this for all 3 hoses.
11. Removed hose from old intake and connected to same location on new intake. Repeated for all 3 hoses.
12. Using pliers, pinched the clips and moved to the end of the new intake valve. Did the for all 3 hoses.
13. Using Phillips screw driver, screwed in the new intake valve where the old intake valve was located.
15. Inserted the wiring connects into new intake valve.
16. Reconnected water hoses back into washer machine (after inspecting and cleaning plastic strainer traps)
17. Turned on water faucets
18. Plugged in washer.
19. Ran an empty load for a cycle.
20. Did not fail.
21. Reattached top to washer. Laying down an inch from front and push forward to hear a click or lock. Then screwed in the 2 screws.
22. Pushed washer back into original location.
We have already performed 1/2 dozen loads.
Read less
Was this helpful?
Thank you for voting!
washer would not run
2 of 3 people
found this instruction helpful.
-
kirk from WEST COLUMBIA, SC
- Really Easy
- 15 - 30 mins
-
Screw drivers
replaced switch as shown in the video...Worked great
Was this helpful?
Thank you for voting!
Water leak from cold water inlet valve
1 person
found this instruction helpful.
-
John from COLLEGE STA, TX
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Looked at videos on line at Parts Select. Very easy instructions to watch and follow. After unplugging the washer all I had to do was turn off the cold water valve, remove the supply line, two screws to get the lid off, then two screws to remove the valve and disconnected the electric connector tabs. Took pliers to back the three hose cl
... Read more
amps off. The best tip was replacing each hose back on the valve one at a time to prevent mix ups. I did everything in reverse after installation. I ran one short cycle to test the leak. Works perfectly!
A tip I saw on You Tube - I have vinyl flooring in my wash room and a repair guy said to spray a light shot of WD 40 under the feet. It doesn’t take much. Man, my washer slid like it was on wheels! I wiped away any excess spray and let it dry under the feet. I’m not sure how this works on other types of floors.
A tip I saw on You Tube - I have vinyl flooring in my wash room and a repair guy said to spray a light shot of WD 40 under the feet. It doesn’t take much. Man, my washer slid like it was on wheels! I wiped away any excess spray and let it dry under the feet. I’m not sure how this works on other types of floors.
Read less
Was this helpful?
Thank you for voting!