WM2016CW (01) LG Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water was filling the tub when washer was not in use.
9 of 9 people
found this instruction helpful.
-
Stephen from BONITA SPGS, FL
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the video and my repair went just like the expert showed on the video. The hardest part was pulling the washer away from the wall and getting enough elbow room to be able to work on the washer. I will definitely come back to this site for my next appliance repair.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud drain pump
7 of 7 people
found this instruction helpful.
-
Gary from HOLLAND, MA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plasti
... Read more
c clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.
Read less
Was this helpful?
Thank you for voting!
Replace leaky water valve
7 of 7 people
found this instruction helpful.
-
JOHN from LOVELAND, CO
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Very simple. Watched video.
Pulled the washer out to get behind it.
Turned off water supply, unplugged it.
Unscrewed the screwesholding the top in place, slid top back, lifted it off.
Used pliers to open the clamps holding the pipes to the valve - one at a time. And fitted the pipes to new valve, one at a time.
SO ... Read more ME WATER REMAINS IN THESE PIPES, SO PUT A TOWEL UNDERNEATH TO CATCH IT.
Removed the electrical connectors one at a time and fitted them to the new valve one at a time.
Did same to the hot valve - not leaking but decided to replace it before it did leak.
Reattached water supply hoses and electric plug.
Tested the washer cycle to make sure no leaks.
Put top back on and pushed washer back to wall.
Apart from the testing, the whole job took 25 minutes.
The parts arrived on Day 2 after the order.
VERY PLEASED WITH EVERYTHING!
Pulled the washer out to get behind it.
Turned off water supply, unplugged it.
Unscrewed the screwesholding the top in place, slid top back, lifted it off.
Used pliers to open the clamps holding the pipes to the valve - one at a time. And fitted the pipes to new valve, one at a time.
SO ... Read more ME WATER REMAINS IN THESE PIPES, SO PUT A TOWEL UNDERNEATH TO CATCH IT.
Removed the electrical connectors one at a time and fitted them to the new valve one at a time.
Did same to the hot valve - not leaking but decided to replace it before it did leak.
Reattached water supply hoses and electric plug.
Tested the washer cycle to make sure no leaks.
Put top back on and pushed washer back to wall.
Apart from the testing, the whole job took 25 minutes.
The parts arrived on Day 2 after the order.
VERY PLEASED WITH EVERYTHING!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Would not run
8 of 11 people
found this instruction helpful.
-
Gary from CPE GIRARDEAU, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers
I followed the instructions of your instant repairman. A Phillips screwdriver was the only tool needed. Thank you .
Was this helpful?
Thank you for voting!
Washer not pumping out and making ominous noises
6 of 6 people
found this instruction helpful.
-
Ray from RIO RANCHO, NM
- Easy
- More than 2 hours
-
Screw drivers, Socket set
Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy.
... Read more
Videos online are your friend.
Read less
Was this helpful?
Thank you for voting!
Water pump went out.
7 of 9 people
found this instruction helpful.
-
Greg from ENUMCLAW, WA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Watch the video to repair and follow along
Was this helpful?
Thank you for voting!
Noisy and drum still full of water . Will not go to next cycle.
6 of 7 people
found this instruction helpful.
-
Marshall from ROSEVILLE, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Follow the LG washer video.
Was this helpful?
Thank you for voting!
w/d repeatedly fills with water during warm or hot loads
5 of 5 people
found this instruction helpful.
-
kevin from WASHINGTON, DC
- Very Easy
- Less than 15 mins
-
Screw drivers
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
Was this helpful?
Thank you for voting!
Water was collecting in the machine after it finished its cycle.
5 of 5 people
found this instruction helpful.
-
Jeffery from NORTHFIELD, IL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Turned off hot and cold water supply. Pulled out machine and disconnected hoses, unplugged power.
Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.
Slid cover back and up. This was the only tric ... Read more ky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.
Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.
Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.
Replace cover. Screw all screws back to secure cover. Replace trays.
Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.
Slid cover back and up. This was the only tric ... Read more ky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.
Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.
Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.
Replace cover. Screw all screws back to secure cover. Replace trays.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.
5 of 5 people
found this instruction helpful.
-
Sandra from Livonia, MI
- Very Easy
- Less than 15 mins
Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
Was this helpful?
Thank you for voting!
None
5 of 5 people
found this instruction helpful.
-
Keineth from DALLAS, TX
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took the one off that was leaking and put the other one on
Was this helpful?
Thank you for voting!
Lower Balance Weight Broken Concrete Internals
5 of 6 people
found this instruction helpful.
-
David from FLORENCE, MA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
The web interface is nice, however in this situation it references the wrong part which was not known until the item arrived. Customer Service handled return, however I had to call LG directly to confirm correct part number (LG p/n 4866ER0004A = p/n PS3524040) but this was only after LG also gave wrong p/n. When replacement part arriv
... Read more
ed the internal concrete had a crack in it. The part is basically a plastic shell that is filled with concrete. However the opening (about 1 x 4) is left open and with the concrete having a crack in it the piece will vibrate together and continue to break down over time (which is what happened to the original one) Before installing I chose to fill opening with epoxy and a plastic layer, then covered with electrical tape to seal it in. I feel this item is poorly designed from LG. Additionally this item was poorly packaged by PS when shipping which caused the damage (it weights about 15 lbs and was allowed to float around in a large over-sized box filled with large air pillows). I have photos but no way to upload here.
Read less
Was this helpful?
Thank you for voting!
Bleach dispenser not emptying.
5 of 6 people
found this instruction helpful.
-
Millie from MANORVILLE, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
First unplug the machine. Turn the water off to the hoses. Remove the hoses from the machine to make it easier. Remove the screws from the back of the top cover. Pry the front sides with a screwdriver and lift. Standing behind the machine on the left side you’ll see the three solenoids or inlet assembly. Remove the two screws so as to tak
... Read more
e the inlet assembly out. There are hoses attached to the assembly.
Read less
Was this helpful?
Thank you for voting!
Washer would not operate. It displayed an error code not described in manual
4 of 4 people
found this instruction helpful.
-
Douglas R. from NEGAUNEE, MI
- Really Easy
- 30 - 60 mins
-
Pliers, Socket set
From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 sec
... Read more
onds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.
Read less
Was this helpful?
Thank you for voting!
Drum spring broke
4 of 4 people
found this instruction helpful.
-
Todd from LAKEWOOD, CO
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.
Was this helpful?
Thank you for voting!