WM2016CW (01) LG Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Inlet hot water valve was leaking.
-
John from Houston, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
1. Unplug washer. 2. Shut off water supply (hot and cold). 3.Remove hot water hose at washer inlet. 4. Remove the 2 plastic pieces that hold the washer top to the washer body by removing the 2 retaining screws. 5. Pull the top back to remove and set the washer top off to the side. 6. Unclip the electric harness from the inlet water valve.
... Read more
7. With your pliers, loosen the clamp on the water inlet valve discharge hose and remove the hose from the valve. 8. Loosen and remove the 2 screws holding the inlet valve to the washer body. Install new hot water inlet valve and follow steps in reverse. Check for leaks before plugging washer back in. Run washer and check for leaks. Note: Excellent video available on You Tube. Consider replacing both the hot and cold water connecting hoses during the repair if they are old.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Water inlet valve coil was leaking water.
-
Robert from Asheville, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.
Was this helpful?
Thank you for voting!
I had a slow leak coming from the factory cold inlet water valve assembly, and removed the top and found it rusted.
-
Drew from Thomaston, GA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.
Was this helpful?
Thank you for voting!
Very visible tear in hose. It was 1 1/2" long
-
Tresa from McHenry, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.
Was this helpful?
Thank you for voting!
leaky inlet valve
-
Michael from Granite Bay, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support
Other Parts Used:
Was this helpful?
Thank you for voting!
Leaking Hot Water Inlet VBalve
-
JOEL from BIXBY, OK
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phi
... Read more
llips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.
Read less
Was this helpful?
Thank you for voting!
Lock assembly displaying DE code
-
Robert from Saugus, MA
- Easy
- 15 - 30 mins
-
Screw drivers
Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring ha
... Read more
rness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.
Read less
Was this helpful?
Thank you for voting!
Drain pump making noise and water wasn't being pumped out
-
richard from rustburg, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed f
... Read more
rom the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.
Read less
Was this helpful?
Thank you for voting!
would not drain
-
Timothy from Williamsport, PA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it rela
... Read more
tively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.
Read less
Was this helpful?
Thank you for voting!
the pump was bad
-
Charles from SMITHVILLE, OK
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
the best video was on you tube and showed exactly how to repair my washer. the parts arrived quickly and was a perfect match. thanks for helping me save some moola and making mama happy.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was leaking
-
Christina from Dickson, TN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I took the back panel off the washer and located where the leak was coming from. It was obviously coming from around where the cold water hose connects. Checked washers in hoses and they were good. Noticed a small drip on the valve assembly that the hose connects too. Took off small panel where the hose connections are mounted....disconne
... Read more
cted all 3 black water hoses that connect to it (squeeze metal clamps with pliers and slide hoses off. and numbered them with permanent marker so I wouldn't get my lines crossed later), removed the quick disconnect electrical lines.... removed part and googled the parts diagram on this site.....identified the part in the pic and ordered....it was here in less than 48 hrs with the basic shipping (which stated 3-5 days:)....reassembled the same way I took it apart. I'm prud of myself, it was pretty easy and I'm sure it saved me a lot of money!:)l
Read less
Was this helpful?
Thank you for voting!
split hose. water leaking on floor.
-
Scott from Parkland, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Loosened hose clamps to remove old bellows. That seemed simple but was awkward reaching into the confined space. Clamp adjustments were all installed facing away from access opening. New one went on easy and I reinstalled clamps facing the opening. Perfect fit!
Was this helpful?
Thank you for voting!
found a leak in the cold water inlet valve- one of the seat gaskets was bad
-
Thomas from Salisbury, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
found a slow leak in one of the valve seat gaskets and decided to replace the entire valve (also did the hot inlet as well just in case). Unplugged unit, detached water hoses (replaced these as well), moved the washer out about 12" from the wall. With Phillips head removed the washer top. With pliers removed the hose clamps off the val
... Read more
ve heading to the detergent dispenser (be sure to keep track of what hose goes to what nipple). Detached electric clip from each solenoid. Using Phillips head removed the valve. Use reverse order to install new valve. Ran the unit through a long cycle with the top off to ensure there were no leaks.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
IE fault code displayed
-
Lyle from Lakewood, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench set
The manufacturer recommends checking the inlet screens first then call for service if problem persists. I checked the screens on the fill solenoids, then I checked continuity for the primary wash solenoid and found that it was bad. I replaced the inlet valve assembly with parts I received from Parts select but I found out later that I had
... Read more
multiple problems. The main PCB had voltage at the main wash fill solenoid contact on the PCB even when the power switch was off. The machine would begin to fill when I would turn the power button on and when no wash mode was even selected. The drain pump would not drain the drum either. I ended up replacing the main PCB and the inlet vlv assembly and pressure switch and now the washing machine works great.I saved myself a boat load of money by doing it myself.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Will not start after dorr is closed. Shows Code dE. Door locks properly, two clicking is heard before code shows up.
-
Juan from Anaheim, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
1. Remove spring-loaded clamp assembly. 2. Partially pull out the large rubber gasket near the lock switch assembly to gain access to the lock switch assembly. 3. Unscrew two screws holding the lock switch assembly. Carefully separate the connector from the lock screw assembly and replace it with the new part. Reinstall in reverse sequenc
... Read more
e. Ensure that the electrical connector is fully seated unto the lock switch assembly and the connector latch is fully set against the lock switch body. Also make sure that the large rubber seal is fully seated around the door opening to prevent water leak. Restarted the washer and everything worked as before.
Read less
Was this helpful?
Thank you for voting!