WM2016CW (01) LG Washer - Instructions

All Instructions for the WM2016CW
121 - 135 of 144

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water not draining from tub, error code "OE"
  • Robert from Ogdensburg, NJ
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!
Was this helpful?
Thank you for voting!
Washer not spinning and giving error message OE
  • Allan from Virginia Beach, VA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is comm on for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.
Was this helpful?
Thank you for voting!
Cloged Drain
  • Darryl from chicago, IL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
My washer would try to spin and remove the water according to the time allowed. Consequently my washer would take longer than the time allowed to drain therefore water would send a code error then the machine would stop working. So I remove the hose from the pump and found my son's little small sock blocking the drain. I removed the sock and reinstalled all hoses. Everything is fine now. No need for a replacement item. Just a little servicing.
Was this helpful?
Thank you for voting!
would not pump the water dry
  • Jinjer from Colorado City, AZ
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
greate very easy and the parts fit awsome the shiping was fast and easy very satified
Was this helpful?
Thank you for voting!
leaking water
  • Gary from Temecula, CA
  • Easy
  • More than 2 hours
  • Pliers, Screw drivers, Wrench (Adjustable)
The most difficult part was moving both the dryer and washer from the laundry room, into the garage. Be sure to unplug and turn off both hot and cold water, gas, and disconnect gas from the dryer before disconnecting hoses and dryer vent. I walked them out with the help of my sweet little wife. I got on utube to find a film on disassembly of the wm2277hs. This is vital because it comes apart like a chinese puzzle box. With the top panel removed, I hooked the garden hose up to the cold side and found the middle solenoid was leaking on the inlet valve. I decided to replace both hot and cold inlet valves along with the four hoses. The hoses had little cracks in them. It cost more but I expect it will save hassle down the road. After replacing the parts, I tested it all with the garden hose, then put it back in the laundry room. Final testing included looking for leaks and dish soap on the gas connection looking for a bubble. Suggest you pay for faster shipping. My stuff came in three separate shipments and took a week. It was about $85 bucks. Good luck.
Was this helpful?
Thank you for voting!
original spider broke
  • Robert from Buxton, OR
  • A Bit Difficult
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench set
remove top and front of washer, disconnect hoses, weights, wires and motor cover from wash tub, remove tub assembly from washer by removing pins from dampers and lift off spring hangers, split washing tub to get to back of drum.unbolt old spider clean all the soap scum buildup and install new part, reassemble washer. works like new.
Was this helpful?
Thank you for voting!
Washer will not drain, bad noise coming from bottom front of washer
  • James from Kingman, AZ
  • Easy
  • 30 - 60 mins
  • Screw drivers
unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.
Was this helpful?
Thank you for voting!
The drain pump impeller broke away from the pump.
  • PAMELA from DE SOTO, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
We drained the water from the washer via the tiny hose/filter located at the lower left corner of the washing machine. The unit was then pulled away from the wall, unplugged and the hoses disconnected. At this time, we used the wet dry vacuum to suction the water that remained in the drain hose. We tilted the washing machine back until the front of the unit was 18 inches or so off the floor. We used the foot stool to hold the washer up in the air so that we could work on the pump. Replacing the pump was as easy as removing a few screws, unplugging the electrical connections and removing the faulty pump assembly from the plastic housing. (Be sure to mark what connector goes in what terminal). Re-assemble. Re-connect. You are ready to go. It took more time to ready the washer than it did to replace the part.
Was this helpful?
Thank you for voting!
Small water leak
  • james from pace, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
First, slide top cover back, then lift of washer. Remember to turn off water supply and disconnect cold water hose before working on valve. Also, unplug washer from wall socket. Disconnect three small electric plugs from valve, noting the postion on valve,then disconnect the water hoses from valve, noting postition of each hose. Remove t wo small screws holding valve to washer,remove and replace valve.reistall valve, reconnect hoses and electric connectors. Reconnect water supply, turn on water supply, check for leak, reconnect power cord to wall socket. Run washer through normal wash cycle, observing water valve for leaks, normal operation, if no problems, then reinstall top on washer
Was this helpful?
Thank you for voting!
not pump water out
  • dung from nashville, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Basic skill
Was this helpful?
Thank you for voting!
Water acculmuation in the drum when not in use
  • JAVIER from BEEVILLE, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I ran the spin & drain cycle to empty the drum,I waited to be see how long it took to see a noticeable level of water in the drum (1-2hrs).decided to check the cold water valve first.Found that there was rust forming around the solnoid piston,making it hang up,most of the time it tryed to open, or close. cleaned with light sand paper(pist on), and ordered part with parts select. Which was real easy,because of the knowledgeable staff,parts came in as promised,and in good shape,and most important of all it was the exact replacement part. My wife is HAPPY,which makes my life good too! THANKS Parts select..
Was this helpful?
Thank you for voting!
door would not lock
  • Eileen from Allen Park, MI
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Used a screwdriver to carefull lift the top of washer. Reached in and unplugged old assembly from wir harness. Unscrewed old one (2 screws) from washer screwed in new one connected it to wire harness. Closed top of washer and plugged it in and it was ready to use. I am a 53 year old female and had never done this before. The repair shop wanted $150 to install part plus the part cost more from them. I' m sure a guy could do the job in 15 minutes or less.
Was this helpful?
Thank you for voting!
water leaking fromdoor
  • Walter from Deland, FL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
remove the front part of the machine to get to the door hinge.
Was this helpful?
Thank you for voting!
OE CODE - The washer machine would not drain
  • Gustavo from Ukiah, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set, Wrench set
After checking for blockage on the drain hose and checking on any blockage on the bottom left corner filter and not finding anything i decided to open the machine. Everything suggested a broken drain pump
ITEM
PS3579318 Drain Pump and Motor Assembly which is located on the bottom left corner also and it attaches to the botto m left corner filter. And voila! The machine did not work! Now started throwing a FE code and it would not fill up. Well, the new pump was stuck! All i had to do was to stick my fingers in the bottom left corner filter orifice and move the fan like devices that make the new drain pump work, that did it! Be careful not to do it while the machine is pluged in, those plastic blades may hurt your fingers. To reach the drain pump you have to take the top, control board and front (door and gasket) of the machine off, about one hour labor.
Was this helpful?
Thank you for voting!
leaking inlet valves
  • George from College Station, TX
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer
Was this helpful?
Thank you for voting!
All Instructions for the WM2016CW
121 - 135 of 144