- Home
- SCA1000DBB03
- Instructions
SCA1000DBB03 General Electric Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Timer, light and control pad worked. Turn table and heat did not work. Oven would not start up.
1 person
found this instruction helpful.
-
Pearlie from Beulaville, NC
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I first read where someone had the same problem. Their solution was a burned-out fuse. I ordered a new fuse...installed it and that did not solve my problem. I revisted PartSelect and read how Marla (from Arlington, TX)solved her problem. I purchased a secondary switch and when it arrived, I made a copy of Marla's instructions and followe
... Read more
d them to the letter. I installed the new secondary switch into the secondary space, put everything back together and the oven STILL DID NOT WORK. I had to take the latching panel apart again and test each switch to see if there was another bad one. I found that the third switch was burned out. So I took the new switch out of the second slot and installed it into the third slot. I tested the switches before reinstalling the latching panel. This time everything worked. So I put everything back together, reinstalled the microwave on the wall, tested it again, and everything worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Microwave would not heat up
1 person
found this instruction helpful.
-
Suzanne from POWELL, OH
- Really Easy
- 15 - 30 mins
Part just snapped into place and wires were reattached.
Was this helpful?
Thank you for voting!
Door Switch went bad, Internal Fan would run every time you open the door
1 person
found this instruction helpful.
-
gilbert from TOMS RIVER, NJ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed the control panel (2 screws), lift up and let hang, with a plan screwdriver open bracket holding the switch, unplug 2 wires, replace with new switch, plug in the 2 wires, push switch back into bracket. Then slide on the control panel, put the 2 screws back. Easy fix.
Was this helpful?
Thank you for voting!
no power in microwave in turn table wouldn't turn light would work act like door was open
5 of 13 people
found this instruction helpful.
-
johnny from port orange, FL
- Easy
- 1- 2 hours
-
Screw drivers
remov cover to check voltage and found problem at the interlock switch ohm the switch and found it was open replace both switches it work fine now
Was this helpful?
Thank you for voting!
The unit would run when the door was open!
1 person
found this instruction helpful.
-
Mike from BLUFFTON, SC
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
First I had to accept the fact that the unit was designed to keep non-professional people from doing any repairs. The switch was installed in such a manner that I had to break the mounting to remove the switch, then drill a hole in the mounting to secure the new switch in place.
Was this helpful?
Thank you for voting!
Turntable Stopped Working/Display Timer Would Countdown But Not Heat
1 person
found this instruction helpful.
-
Steve from Wesley Chapel, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
With this model, you must remove the outer covering. Don't try to access the display unit from the front like I've seen in some other GE microwave videos. After removing the outer covering, the switches are easy to replace. They are very visible and easy to get to without taking any other parts off. You will see the door switches just
... Read more
behind the display board. Remove the switch and then remove the connecting wires to ensure you don't inadvertently brake a wire. You will need a tamper resistant star bit to remove 3 or 4 screws from the back panel. All other screws are philips head. I went ahead and replaced both switches (yes...there are two of them) and works like a charm. I saved an $800 microwave for less than $60 and know what to do if it happens again. Appears to be a common problem on this model. Thanks for others making a post...It saved me time and money reading others remarks. Good luck!
Read less
Was this helpful?
Thank you for voting!
Microwave wouldn’t heat
1 person
found this instruction helpful.
-
Rex from ROSEVILLE, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I want to preface this review by stating that I do some DIY from YouTube, but have no experience in electronic repair. The microwave is over the stove with the extendavent. First I unplugged the microwave, removed the vent and started to unscrew the microwave from the mount. I used a power drill to speed things up. I was able to remove
... Read more
the microwave on my own. I unscrewed the lid on the microwave and took the lid off and there is the magnetron. I opened up needle nose pliers to have each end touch the terminals of the capacitor (holds the power, Dangerous). I made sure to keep my hands on the rubber handles and avoid touching the metal part of the pliers. I used the pliers to remove the plug of the capacitor to the magnetron as well. The magnetron has 4 screws (2 top, 2 bottom). There is a magnet that can hold the screws to keep from falling but I’d still recommend a screwdriver with a magnet on the end. The magnetron has another set of wires connected by a metal bracket like a holder, not really connecting any wiring to the magnetron itself. I had to unscrew 1 screw to removed that. Adding everything back on was easy, same steps back. I plugged in the microwave and tested a cup of water before I mounted it back above the stove. Voila! I did need my wife’s help to hold the microwave on the hinge while screwing into the mount. It doesn’t take a lot of muscle for the help. $85 for the part and ~40 mins to fix a $400 microwave!
Read less
Was this helpful?
Thank you for voting!
Unit would not heat
1 person
found this instruction helpful.
-
william from LA VERNE, CA
- Easy
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Used a Motor cycle Jack to remove both unites combined. Removed side panels exposing internal working parts. Removed nonworking Magnetron and replaced it with new Magnetron. The process was completed in about 1 hour.
Was this helpful?
Thank you for voting!
broken latch
1 person
found this instruction helpful.
-
Wilson from Pembroke Pines, FL
- Easy
- 30 - 60 mins
-
Screw drivers
We used the scresdriver(flat) to remove the frame inside the door, the remove several screws retaining the inner part of the door thenremoved the broken piece. We replaced the latch with the spring With a little patience, everything went fine. I broke one of the small tab, no big deal.
thanks, you saved me a lot of money/.
thanks, you saved me a lot of money/.
Was this helpful?
Thank you for voting!
Door latch assembly
1 of 2 people
found this instruction helpful.
-
Garry from HILTON HEAD, SC
- Easy
- 30 - 60 mins
-
Screw drivers
Read other folks on your site on how they did it and I followed their directions. About 30 minutes and it was done. Figured I saved lots of money. Thanks
Was this helpful?
Thank you for voting!
installed new kitchen cabinets
1 of 2 people
found this instruction helpful.
-
andrew from HOMOSASSA, FL
- Easy
- 15 - 30 mins
the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original m
... Read more
ounting bracket. It was a perfect fit and the install went great
Read less
Was this helpful?
Thank you for voting!
Glass turntable broke when being washed.
1 of 2 people
found this instruction helpful.
-
Lee from Spartanburg, SC
- Really Easy
- Less than 15 mins
Ordered the part on Monday, it was delivered on Wednesday, only paid for standard shipping. All I had to do was put it in, right part, back to new!
Was this helpful?
Thank you for voting!
Thermostat quit.
1 of 2 people
found this instruction helpful.
-
Tony from ITHACA, MI
- Easy
- Less than 15 mins
-
Screw drivers
Checked all sensors with a multi-meter, found the thermostat to be the problem, no continuity.
Was this helpful?
Thank you for voting!
Handle broken
7 of 21 people
found this instruction helpful.
-
Diane from North Palm Beach, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed plate inside door cover and removed old screws and plastic handle. Reassembled.
Was this helpful?
Thank you for voting!
Broken handle
1 of 3 people
found this instruction helpful.
-
Kent from NAPA, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Removed inner trim panel. Bottom screw was visible But upper screw was behind metal frame that trim plate snaps onto Removed that to access screw. Door latch had to be removed to. Not a big deal just be sure spring on latch is reinstalled same way it was removed. Took longer than expected but way cheaper than a service call. Part arrive
... Read more
d on time
Read less
Was this helpful?
Thank you for voting!