- Home
- SCA1000DBB03
- Instructions
SCA1000DBB03 General Electric Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
install new latch and spring in door
3 of 10 people
found this instruction helpful.
-
Clifford from Springfield, VA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
removed key pad then removed latch assembly and replaced it with new latch assembly.
Other Parts Used:
Was this helpful?
Thank you for voting!
Replacement of Magnetron
0 of 1 people
found this instruction helpful.
-
Benjamin from Anchorage, AK
- Really Easy
- 15 - 30 mins
-
Screw drivers
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations
... Read more
on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Read less
Was this helpful?
Thank you for voting!
no heat
0 of 1 people
found this instruction helpful.
-
Nelia from Streamwood, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this helpful?
Thank you for voting!
cover fell apart
0 of 1 people
found this instruction helpful.
-
Esther from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!
Was this helpful?
Thank you for voting!
No heat
0 of 1 people
found this instruction helpful.
-
Edwin from New York, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replace the fuses
Was this helpful?
Thank you for voting!
No heat.
0 of 1 people
found this instruction helpful.
-
Mack from Jacksonville, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replaced the fuse. Result; did not fix the problem.
Was this helpful?
Thank you for voting!
Knob became worn.
-
Joseph F from Clarkston, MI
- Really Easy
- Less than 15 mins
Couldn't find the exact part using the online service but called and the customer service operator got me precisely what I needed - she was fast, friendly and very helpful. I had a great overalll experience.
Was this helpful?
Thank you for voting!
I broke the glass tray
-
Kimberly from San Tan Valley, AZ
- Really Easy
- Less than 15 mins
I'm writing because I have never in my life had such an easy time finding a part, ordering it, and receiving it! Your service is truly unbelievable. I still don't believe it and I experienced it. Nothing went wrong and it could not have been easier. Please don't go away.
Was this helpful?
Thank you for voting!
Glass rotating tray cracked and broke when cooking
-
paul g. from westlake village, CA
- Really Easy
- Less than 15 mins
This is the tray the glass cooking tray rest on and rotates the glass during cooking. The metal tray was installed upside down. The rotating glass tray was not properly installed. The oven was at a very high temp. and the weight of the utensil on the glass was not supported correctly. Result, big " pop " and broken glass tray. Note this
... Read more
is the second glass repaced. The first one dropped while removing it from the oven. It stuck to the bottom of the cooking dish and then fell to the floor. Pop, big breakage. Maybe you can learn from my mistakes.
Read less
Was this helpful?
Thank you for voting!
drop and shattered the glass tray
-
Nicole from Lathrop, CA
- Really Easy
- Less than 15 mins
It was so easy to order the part on this website. It came carefully packaged and quickly! Thank you!
Was this helpful?
Thank you for voting!
Glass tray broke in microwave
-
Ralph from Puyallup, WA
- Really Easy
- Less than 15 mins
Removed tray from shipping container and installed in the microwave.
Was this helpful?
Thank you for voting!
Old vent grille was broken at the two connecting points.
-
William M. from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Unscrewed the two connecting points, cleared out the broken bits of plastic, mounted the new grille and screwed the two screws back in. Easy. Also, the new part arrived very quickly.
Was this helpful?
Thank you for voting!
Broken Glass Tray
-
ISAAC from MADAWASKA, ME
- Really Easy
- Less than 15 mins
Very easy replacement. Just lift out and replace with a new one!
Was this helpful?
Thank you for voting!
microwave won't heat
-
Stephanie from Kernersville, NC
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Was this helpful?
Thank you for voting!
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
-
Pines, from Middletown, NY
- Really Easy
- Less than 15 mins
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Was this helpful?
Thank you for voting!