- Home
- SCA1000DBB03
- Instructions
SCA1000DBB03 General Electric Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken microwave glass tray
-
Frank from Arlington, VA
- Really Easy
- Less than 15 mins
Placed the new tray in the microwave.
Was this helpful?
Thank you for voting!
Change a burnt out bulb
-
George from Fort Myers, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Opened the lid over the bulb by removing one screw. Removed old bulb; a bayonet type with delicate prongs. Inserted new bulb. Best to turn off circuit breaker toi the micro for safety reasons.
Was this helpful?
Thank you for voting!
Microwave handle broke
-
Lane from Melbourne, FL
- Easy
- 30 - 60 mins
-
Screw drivers
Remove door from unit. Place on cushioned service. Carefully pry plastic frame on inside of door to expose upper screw hole for handle. To gain access to lower screw hole, the inner metal frame must be removed. First, remove screws holding metal frame to door. Now carefully pry back the plastic tabs on each side. Once tabs are freed
... Read more
, metal frame easily removes. Install new handle, snap metal frame back, reinsert metal screws, then resnap plastic frame into place.
Read less
Was this helpful?
Thank you for voting!
microwave just stopped working
-
James from Fall Branch, TN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.
Was this helpful?
Thank you for voting!
latch and handle were broke
-
Ruanne from Kent, WA
- A Bit Difficult
- 30 - 60 mins
take the door off. The door lifts up and off. Once on a flat surface the job became must easier
Other Parts Used:
Was this helpful?
Thank you for voting!
Could not be turned on
-
Remer from Dothan, AL
- Really Easy
- 1- 2 hours
-
Screw drivers
Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.
Was this helpful?
Thank you for voting!
Replaced door handle after 3 years of super glue
-
Todd from Benicia, CA
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
The instructions were great!!! It was difficult to take the face plate off without breaking the nibs off that hold it in place. Other then that the only issue I had was removing the broken piece that was cemented in place by the years of super glue. Had to drill it out and almost drilled out the receiver plate to hold the screw/handle in
... Read more
place. I have to say this saved me $400 because I was just about to buy a new microwave because the broken door handle had driven me crazy over the last 3 years.
Read less
Was this helpful?
Thank you for voting!
Door Interlock Switch Failed
-
Michael from Littleton, CO
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers
Removed cover, diagnosed problem, ordered part from Parts Select, received part in 2 days, replaced part, tested and replaced oven into built in space.
Was this helpful?
Thank you for voting!
Door handle broken
-
Thomas from Washington, DC
- Very Difficult
- 1- 2 hours
-
Pliers, Screw drivers
This wasn't easy to do, it would have been better to have two people. Taking the plastic trim off the inside of the door is tough, and only gets you access to the top screw. (You need to take that trim off to remove the door, and you have to put the door back on before you put the trim back, by the way.) You have to remove the shield cov
... Read more
ering the glass in order to get to the bottom screw. I didn't think I'd be able to get that shield off, and another set of hands to help pry it up would have been helpful. All in all, it's worth doing because the part is only $40 or so, but I can't call it an easy fix. Also, since the top of the handle had broken where the plastic screw sleeve meets the handle, and the screw was still inside the sleeve, it was almost impossible to get the screw out. Needlenose pliers wouldn't do it. I finally had to use a drill to drill away at the plastic sleeve until it was almost completely gone to get the screw out.
Read less
Was this helpful?
Thank you for voting!
Timer operated normally, but the microwave did not heat water or cook food.
-
Peter from Severna Park, MD
- Difficult
- More than 2 hours
-
Pliers, Screw drivers
Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts.
... Read more
He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Problem door latch
-
Ron from Southampton, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks
Was this helpful?
Thank you for voting!
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
-
Sam from Chandler, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch a
... Read more
ssemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.
Read less
Was this helpful?
Thank you for voting!
broken latch hook
-
David from Pittsburgh, PA
- Easy
- 15 - 30 mins
Removed. Inside frame with putty knife replace new latch attach spring and line up notch of latch in slots. That was the most difficult part replace inside frame. Done!
Was this helpful?
Thank you for voting!
Microwave would turn on ,BUT turn table would not turn and oven would not heat.
-
Earl from New Philidelphia, OH
- Easy
- 15 - 30 mins
-
Screw drivers
Took off cover , unpluged switches , took off switch assy, off/on test hooped and howlered for about 5 mins .Then laughed about other sites said could get those switches. Just wanted to say I LOVE Partselect. Super fast del , great price. JUST AWSOME!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
Just recently fixed and my son broke it a week later...
-
Amy from Hillburn, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...
Was this helpful?
Thank you for voting!