- Home
- SCA1000DBB03
- Instructions
SCA1000DBB03 General Electric Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Handle Broke off microwave
7 of 13 people
found this instruction helpful.
-
Dara from Tampa, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the vent on top. 2 screws had to be removed. Once plastic vent was removed I could lift door off. I then placed the door flat on counter top to get to backside of door. With 2 flat screwdrivers I pried apart the Door choke cover carefully as to not break the tabs. Its almost impossible not to break them. Thats why I orde
... Read more
red the replacement part. Good thing. I only broke 1. I could have reused it. However I chose to use the new one. Since handle in incorporated in the door, you have to take the door apart. I purchased the Door choke cover as well as a handle. After you remove the choke cover, remove the 6 or 7 small screws around the inner frame next. Now you can get to the door handle screws. Since the door handle broke off, you need to use needle nose pliers to hold the broken plastic on the outside of the door while unscrewing the inside screw that holds the handle. Once removed. replace the handle. Then carefully put it back the same way you took it apart. It took me about 15 to 20 minutes. Im a Female and thrilled I didn't have to call a repairman and get charged 200+
Read less
Was this helpful?
Thank you for voting!
door latch arm broken, microwave wont start
4 of 4 people
found this instruction helpful.
-
Kent from KANSAS CITY, MO
- Really Easy
- 15 - 30 mins
-
Pliers
This was easier than I had expected. Many of the instructions involved removing the door. I decided to skip this when I found a Youtube video showing that the latch replacement required little disassembly. Here are my steps #1 Open door completely and, if needed, have someone steady it. #2 Using a thin plastic putty knife, gently pry
... Read more
off the plastic fascia from the inside of the door. Try to break as few of the plastic retaining tabs as possible (my total was about 10). #3 Slide the old latch upward and outward towards the outside edge of the door with your putty knife. #4 Remove the old latch and spring. #5 Attach the new spring to the latch and hook it to the retainer on the door. #6 Lift the new latch into place, it will drop into the slots with no or little persuasion. #7 reinstall fascia. #8 "nuke" last night's pizza ;)
Read less
Was this helpful?
Thank you for voting!
mICROWAVE WOULD NOT HEAT
5 of 8 people
found this instruction helpful.
-
Peter from Bessemer, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
I REMOVED THE TOP PANEL OF THE MICR0WAVE AND THEN REMOVED ONE SCREW TO REMOVE THE CONTROL PANEL. rEMOVED OLD SWITCH. SNAPPED IN NEW SWITCH AND CONNECTED WIRE. REPLACED CONTROL PANEL AND UPPER PANEL.
Was this helpful?
Thank you for voting!
Installing New Microwave
5 of 9 people
found this instruction helpful.
-
Tom from Carrollton, TX
- Really Easy
- 1- 2 hours
-
Screw drivers
Required removing the old unit and disconnecting the exhaust ductwork and drilling new holes for attachment to the cabinet
Was this helpful?
Thank you for voting!
Would not heat and made a buzzing or popping sound
4 of 7 people
found this instruction helpful.
-
Thomas from NEWARK, DE
- Easy
- 15 - 30 mins
-
Screw drivers
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other
... Read more
and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
Read less
Was this helpful?
Thank you for voting!
Glass tray somehow got a nick in the edge, a few days later it split while in use.
3 of 4 people
found this instruction helpful.
-
Delores from Portland, OR
- Very Easy
- Less than 15 mins
Another company said the new plate would arrive in mid-March, this company seemed to be faster so ordered the tray here, and it came in less than a week. I put the turn button back in the center hole, set the wheeled ring on the bottom of the oven, fitted the new glass tray onto the turn button.
Was this helpful?
Thank you for voting!
Old wave guide cover deteriorated from cleaning
5 of 10 people
found this instruction helpful.
-
Larry from Colbert, WA
- Easy
- Less than 15 mins
-
Screw drivers
Removed one phillips head screw, removed old cover, then replaced new cover and screw. Very easy and Parts Select made it happen. Will deal with them again. Thanks Parts Select.
Was this helpful?
Thank you for voting!
Origional wave guide cover fell apart from harsh cleaners
4 of 7 people
found this instruction helpful.
-
Joseph from Staten Island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed one Phillips screw, installed new wave guide cover, secured with phillips screw. Done
Was this helpful?
Thank you for voting!
I broke the vent grille on my microwave trying to remove it for cleaning
4 of 8 people
found this instruction helpful.
-
Nancy from Franklin, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair was easy, just two screws but I was very impressed with the price and swift delivery of the part from PartSelect.com. The vent grille was almost $40 less than it cost on the GE website and I had the part in 3 days. Thanks!
Was this helpful?
Thank you for voting!
Frost build up on bottom to ice bin and delivery chute in door creating ice blockage
3 of 5 people
found this instruction helpful.
-
Ronald from PONCA CITY, OK
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove the ice bin.
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of t ... Read more he freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Turn the ice maker selection to "OFF"
Use small flat blade screwdriver to open the plastic ears on the electic plug in connectiion
Use #2 Phillips screwdriver to remove the screw on the front left side of the ice maker
Pull the ice maker forward until free of the two studs in the left side rear of t ... Read more he freezer wall
Check to see if the supplied water chute is the correct size for your application, if not remove the water chute from the old ice maker and place it on the new one.
Place the new ice maker in the freezer connecting the slots on the left read with the studs on the left wall
NOTE; IF THE ICE MAKER DOES NOT APPEAR TO BE LEVEL HORIZONTALLY REMOVE IT AND CAREFULLY REINSTALL IT TO ACHIEVE LEVEL
NOTE: ENSURE THE WATER DELIVERY TUBE RESTS IN THE RECEIVER TRAY
Reconnect the electrical plug ( needle nose pliers may be helpful in aligning the male plug with the female plug)
Move the selector from "OFF" to "ON"
Replace the ice bin and close the freezer door
Read less
Was this helpful?
Thank you for voting!
Door latch broken
2 of 2 people
found this instruction helpful.
-
Kathy from SAN DIEGO, CA
- Very Easy
- 15 - 30 mins
-
Screw drivers
I read your instructions sent with the new latch. Looked at a couple videos online and it was VERY easy to change the part. Thanks so much?
Was this helpful?
Thank you for voting!
Door Latch Assembly Broke
2 of 2 people
found this instruction helpful.
-
Raymond from RIVER RIDGE, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers
This is a simple task. Removed the choke cover using a putty knife or small flat screw driver. Putty knife works best. Slide putty knife under the plastic choke cover to lift up over clips all around the door. There are 3 on top and Bottom and 2 on each side. Be very careful or you will break the catch clips that hold the choke cover
... Read more
in place. Lift the door latch up all the way and push towards the outside of the door, then pull the top or bottom out then the rest of it. Unhook the spring end from the door. Attach the new spring to the hook on the door and then to the door latch. Extend it up all the way so the 2 hook parts of the door latch can go back into their slots. Unlike some others said, the microwave door does not need to be removed. If you have someone to hold the door still, that's good enough. I did it by myself with no problem.
Read less
Was this helpful?
Thank you for voting!
Microwave not turning on. All other functions operate
2 of 2 people
found this instruction helpful.
-
Tom from DENVER, CO
- A Bit Difficult
- 1- 2 hours
-
Screw drivers
DISCONNECT THE POWER CORD and discharge the capacitor
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switc ... Read more hes (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Leave unplugged overnight
Remove vent grille by removing the 2 philips screws
Remove the LED panel by removing 1 phillips screw
Disconnect all connectors that plug into back of the LED board completely
Remove the wires from the switc ... Read more hes (3) at the inside edge of the microwave door
Gently remove each switch housing and test all three switches for continuity
Carefully replace non-functioning switches and reassemble the panel
GOOD LUCK
Read less
Was this helpful?
Thank you for voting!
Broken microwave door latch.
2 of 2 people
found this instruction helpful.
-
Galen from SAN SABA, TX
- Really Easy
- 30 - 60 mins
-
Screw drivers
Watched Utube instructions on how to do it to it and just did it.
Was this helpful?
Thank you for voting!
the TCO is a temperature fuze on the side of the exhaust outlet. When the exhaust registers too high a heat temperature the fuze blows and stops the entire unit from working.
2 of 3 people
found this instruction helpful.
-
James C from ARLINGTON, TX
- Easy
- 15 - 30 mins
-
Screw drivers
I replaced the TCO (fuze) through the vent opening after removing the vent cover and several small panels with a screw driver for visible access.. Some of the screws require a small offset screwdriver because of the limited access. I did not have to drop the unit from the wall over the range and was able to access through the vent openi
... Read more
ng to replace to failed TCO with a new one. The TCO is wired in-line with the power and other fuses to the unit and when it fails the enitire unit is cold with no power to lights or function of any kind. The GE service rep. said that the unit needed a new smart board but that was not the problem and they are no longer made for the older unit. I discovered the repair by looking at YouTube for repairs for the GE Advantium 120 microwave/convection combo unit.
Read less
Was this helpful?
Thank you for voting!