SCA1000DBB03 General Electric Microwave - Instructions

All Instructions for the SCA1000DBB03
31 - 45 of 143

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Blown fuse in microwave
8 of 9 people found this instruction helpful.
  • Frank from VIPER, KY
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
One small Phillips screwdriver and one fuse puller (I used cord). Unplug unit. Remove the two screws on the vent face plate. Remove the one screw on the panel assembly. Gently let hang. Pull the fuse located on the upper left wall. Replace fuse. Reassemble.
Was this helpful?
Thank you for voting!
burned out light surface light bulb
10 of 16 people found this instruction helpful.
  • Veronica from St Augustine, FL
  • Easy
  • Less than 15 mins
  • Screw drivers
the main issue I had is the appliance manual stating that the bulb should be "unscrewed". when I first read the manual, before I received the bulb on delivery, I tried "unscrewing" the bulb, which actually is a PLUG IN bulb. small wonder that it didn't come out! luckily I didn't break the connections off in the socket!
Was this helpful?
Thank you for voting!
Need to replace broken door handel on microwave oven!
12 of 23 people found this instruction helpful.
  • Raymond from Oklahoma City, OK
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Finnaly found exploded view of door, but had to guess how to remove snap in escution that covered the screws. Broken end of old handel piece spins with screw, so I am waiting for help to hold the front end, so I can remove the screw from the other side. Repair has yet to be completed!
Was this helpful?
Thank you for voting!
microwave would not heat
14 of 29 people found this instruction helpful.
  • John from Erie, PA
  • Easy
  • 30 - 60 mins
  • Screw drivers
First remove all screws holding on outer metal casing of microwave. Next remove the back and bottom metal pieces. You will then be able to pull aside the outer casing so you can access the door switches. Check each switch with an ohm meter in both the open position and with the switch closed. If the ohm meter reads the same in both the open and closed position, the switch is bad. Check the top switch first. Replace switch and reassemble. Cheap fix for a costly microwave. Great customer service at Parts Select!
Was this helpful?
Thank you for voting!
Motor would slip and make a grinding noise when anything heavier than a cup of coffee was placed on the table
11 of 21 people found this instruction helpful.
  • James from Export, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Remove the bottom of the microwave and remove/replace table motor.
Was this helpful?
Thank you for voting!
Broken Vent Grille
9 of 15 people found this instruction helpful.
  • Peter F from Daytona Beach, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The repair was very simple. I removed the broken grille and replaced it with the new one using only a screw driver . The procedure took less than five min. I was very pleased with the price of the new grille, which was less than the you know who, and how fast it took the part to reach my home. You get an a+ from me.
Was this helpful?
Thank you for voting!
burnt out bulb
13 of 27 people found this instruction helpful.
  • Neal from Gardena, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
removed light cover and replaced defective bulb
Was this helpful?
Thank you for voting!
The bottom latch of the latch/spring assembly had broken off
8 of 13 people found this instruction helpful.
  • Charlotte from Leawood, KS
  • Easy
  • Less than 15 mins
First I removed the inside of the door using a putty knife and loosening the edges. I removed the old latch by- (1) lifting up and sliding both the top and the bottom out of the door (2) pulling out the bottom part and (3) using a small plastic fork to push the spring off of the top part (paying close attention to how it was already sit ting in the microwave). It required a little twisting (not much) and it came out.

I put the new spring on the new piece on the hook part. Then I put the new spring on the oven (where the old spring had been). I stretched the latch up and put the top slot back in and then with a little (very little) pressure I popped the bottom back in.
Was this helpful?
Thank you for voting!
Magnitron failed
8 of 13 people found this instruction helpful.
  • Joseph from WILTON, NH
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover .
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.
Was this helpful?
Thank you for voting!
I needed to acquire and install a mounting plate for an over the range microwave
9 of 17 people found this instruction helpful.
  • Roy from Lakewood, CO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I attached the mounting plate to the wall as directed in the installation instructions which I had downloaded from GE. This procedure took 45 minutes to complete. I was then able to mount the microwave.
Was this helpful?
Thank you for voting!
original wave guide went flakey & fell apart
7 of 11 people found this instruction helpful.
  • Norman L. from West St. Paul, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The actual repair required removing wave guide held in by one phillips screw was easy.

Thanks much for your rapid dependable delivery!!!

Norm Goetzke
West St. Paul, MN.
Was this helpful?
Thank you for voting!
the glass circular tray inside had cracked in half.It was of no use. I reordered another
5 of 6 people found this instruction helpful.
  • patty from SEATTLE, WA
  • Very Easy
  • Less than 15 mins
The tray came within 5 days and I simply took it out of its well-packaged box and slipped it into my microwave. It is working just like new. I can't thank you all for being so punctual and reliable. better than having to buy a brand new microwave.
Was this helpful?
Thank you for voting!
Microwave went totaly blank - No power
8 of 15 people found this instruction helpful.
  • Mark from Bushwood, MD
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Wrench set
Disassembled the front cover, found slow blow fuses, then replaced with microwave fuses 250V-20Amp. Utilized a few fuses to pin point the problem, Microwave functions all worked except the express feature, made an assumption after using a tester that it was the high voltage capacitor and the diode that attaches. Replaced both, plugged in and tested. Worked! reinstalled the unit. Sucessfull for the past month.
Was this helpful?
Thank you for voting!
Opened door to get food put more food in closed door it wouldnt work
4 of 4 people found this instruction helpful.
  • Henry Totten from GROVES, TX
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Everything worked on the display light inside worked but when you closed the door and set time it would start counting down but not heating nor would the turntable turn. Started reading troubleshooting chart and first thing I did was removed the cover and checked door switches and found primary door switch wasn't working so I ordered a ne w one installed it and it worked. Anyone doing this has to be very careful because of the stored energy in the capacitor is strong enough to kill.
My micro is only 2 years old so I was hoping it wasn't anything major.
Was this helpful?
Thank you for voting!
Handle broke off
11 of 25 people found this instruction helpful.
  • Jeremy from Indianapolis, IN
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Had to remove the interior cover of the door to access the handle screws. Remove these screws and insert the new handle. This is a stovetop model so between the constant pushing and pulling on the handle together with the heat from the stove, the handle breaks. This is the second time I've had to replace it in 5 years...but again, it's an easy inexpensive fix.
Was this helpful?
Thank you for voting!
All Instructions for the SCA1000DBB03
31 - 45 of 143