- Home
- 110C68132413
- Instructions
110C68132413 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
noisy dryer
1 person
found this instruction helpful.
-
Thomas from MYRTLE BEACH, SC
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes
Was this helpful?
Thank you for voting!
Catch broke
1 person
found this instruction helpful.
-
John from NORTH HAVEN, CT
- Very Easy
- Less than 15 mins
-
Screw drivers
Unscrewed the inside part of the door from the outside door shell. Removed the broken pieces of the catch and replaced it with the new one. Screw the door back together. Did not need to remove the door from the dryer cabinet.
Was this helpful?
Thank you for voting!
Loud scratching noise, very loud
1 person
found this instruction helpful.
-
Mark from Linthicum Heights, MD
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Lubricated pulley wheel which temporary reduced noise. This verified what was making noise. Looked up the part on partselect.com and ordered it. Recieved idler pulley with bracket in just a few days.
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and r ... Read more emoved old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Quickly removed back panel using nut driver with drill. Slipped belt off pulley, removed one screw with plyers to released spring and r ... Read more emoved old assembly.
Inserted new assembly, connected spring, slipped belt back on roller.
Tested before replacing back panel.
All was very quiet. Replaced back panel.
All done
Read less
Was this helpful?
Thank you for voting!
Loud squealing noise during operation
1 person
found this instruction helpful.
-
gerald from LEBANON, PA
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Turn off electric to unit.
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulle ... Read more y lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Remove lint trap.
Remove lower cover below dryer door. 1 grey clip on either side. Bend upper portion of the clip down while pulling forward on panel.
Remove 4 1/4 inch bolts that hold blower duct to fan.
Push pulley upward while removing belt.
Use a small angled pick to remove pulle ... Read more y lock ring.
Install new washer and pulley. I added grease to pulley shaft.
Hope this helped. Good luck
Read less
Was this helpful?
Thank you for voting!
Noisy, screeching, sounded like roller bearings were shot
1 person
found this instruction helpful.
-
Henry from CHEYENNE, WY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Watched the video, followed the printed instructions for reminder when necessary. Needed a second person briefly to hold the dryer tub when installing the new belt, and also when removing/replacing the front panel. Beyond that, it was straight forward and relataively easy to do. Solved the noise problems and it dries more evenly now as
... Read more
well. The one thing the instructions don't say is to check the rear canvas seal when the tub is re-inserted into place to assure it doesn't fold back on itself.
Read less
Was this helpful?
Thank you for voting!
The dryer would shut off mid-cycle.
1 person
found this instruction helpful.
-
Michael from ONEONTA, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dry
... Read more
er works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
Read less
Was this helpful?
Thank you for voting!
Squeaky tension pulley
1 person
found this instruction helpful.
-
Trevor from Puyallup, WA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Very easy repair... The video was really helpful too. I was able to find a different video that was closer to our model. (Front Loader HE) It probably took me a little longer than needed but I took the time to shop-vac everywhere I could, since it was all easy to get to. I opted for next day shipping so the shipping charges were more than
... Read more
the part. Tools I used were: Cordless drill-screw driver, 1/4in. socket, Phillips head bit and needle nose pliers for the control panel connections. Thank you again for making this so easy. Saved us a lot money by not calling an appliance repair tech.
Read less
Was this helpful?
Thank you for voting!
Idler pulley broke off.
1 person
found this instruction helpful.
-
Edwin from PASADENA, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took back panel off, and it was really easy putting the new idler pulley in.
Was this helpful?
Thank you for voting!
Loud squeal noise when dryer running
1 person
found this instruction helpful.
-
Joseph from Canonsburg, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.
Was this helpful?
Thank you for voting!
The plastic part on the door catch was broken
1 person
found this instruction helpful.
-
Cindy from ENUMCLAW, WA
- Easy
- 30 - 60 mins
-
Pliers
I removed the metal piece which held the plastic "catch". There were no screws, squeeze to remove it. Then inserted the plastic part and re-inserted the metal part into the dryer door. Very simple. But even more pleasing was the easy ordering and the quick delivery of the part! Thank you so much!
Was this helpful?
Thank you for voting!
F-26 Fault message
1 person
found this instruction helpful.
-
DW from ALVIN, TX
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this helpful?
Thank you for voting!
replace idler pully
1 person
found this instruction helpful.
-
curtis from STOCKBRIDGE, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
first of all there is no video for this model dryer (cabrio accu-dry) the main difference is that the console is removed by removing 3 screws across the back top of console then using putty knife release spring fastener on each side ,slide forward and lift. remove one screw at top of control board and remove from plastic mount,and unplug
... Read more
connecting wires.remove top of cabinet lifting up and forward. The rest of install is typical to other models. The back panel doesn't come off this model. You have to access everything from the front.
Read less
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person
found this instruction helpful.
-
Joe from St. Louis, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
pulley bad
1 person
found this instruction helpful.
-
Dean from MAGNETIC SPGS, OH
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
pull the back off and replace the pulley.
Was this helpful?
Thank you for voting!
Pulley wheel broke apart
1 person
found this instruction helpful.
-
George from CLIFTON, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Disassemble dry. Put on new pulley wheel. Greased pulley wheel. Put dryer back together. Works great. Yours truly G.B.
Was this helpful?
Thank you for voting!