110C68132413 Kenmore Dryer - Instructions

All Instructions for the 110C68132413
106 - 120 of 211

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer was making bad noises like a bearing was going out, then it got worse and sounded really loud, so I couldn't even run it.
1 person found this instruction helpful.
  • Margo from FOX ISLAND, WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.
Was this helpful?
Thank you for voting!
belt worn
1 person found this instruction helpful.
  • Allan from JOHNSTON, RI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
replaced rollers, belt and pulley. Video was very helpful
Was this helpful?
Thank you for voting!
drum roller were worn out
1 person found this instruction helpful.
  • STEVE from FULDA, MN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
flipped up the top pulled the front off easy access to drum removed the drum replaced rollers per instructions that came with package. very eas job. works great.
Was this helpful?
Thank you for voting!
Drum wouldn't move. Belt Broken.
1 person found this instruction helpful.
  • William from HUDSON, MI
  • Really Easy
  • 30 - 60 mins
  • Pliers, Socket set
Opened the cabinet and removed the drum. Cleaned out the dryer fuzz. found that the roller stabilizer wasn't in place; apparently due to a previous repair. Replace both rollers and the roller stabilizer and prepared to replace the drum. But because I live alone, I didn't have anyone to hold the drum while I connected the belt to the motor . But, I did have three unused balloons which I partially inflated and set the drum on them in the bottom of the cabinet while I hooked up the belt to the motor. Put everything back together and it is now drying my clothes again. :)
Was this helpful?
Thank you for voting!
Dryer was making loud noises.
1 person found this instruction helpful.
  • Larry from PHILADELPHIA, PA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.
Was this helpful?
Thank you for voting!
My dryer was not getting hot.
1 person found this instruction helpful.
  • Ronnical from Napanoch, NY
  • Really Easy
  • More than 2 hours
  • Socket set
The first thing I did was to watch the video from Part select on How to change thermostat cut off switch and the high limit thermostat fuse.I did not have a meter reader I just brought the thermostat cut off kit for about $ 32.00 dollars from part select and replace both part's and my dryer still was not getting hot so back to part select video's I looked up the video on replacing the heater element and I ordered one for about $ 97.00 with shipping I replaced it and put it back together and it worked it took just a few hours . I would like to give Avery special thank to part select for the video help and for having the parts for a great price again thank you so much.
Was this helpful?
Thank you for voting!
broken plastic catch on dryer door
1 person found this instruction helpful.
  • Ann from Brenham, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers
removed broken parts & snapped in new catch
Was this helpful?
Thank you for voting!
Sqeaking Belt Drum wouldn't turn
2 of 5 people found this instruction helpful.
  • Todd from Oneida, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Unpluged Dryer
Removed the two screws by the lint screen
Lifted the top of the dryer up by using a putty knife to push in the locking clips that hold the top down
unhooked door wiring switch
Removed the front door panel
Removed drum
Shop vac the unit
replaced the worn parts
reassembled the unit
Was this helpful?
Thank you for voting!
Loud squeaky sound at start up
1 of 2 people found this instruction helpful.
  • DANIEL from FOND DU LAC, WI
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Socket set
Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!
Was this helpful?
Thank you for voting!
Dryer was making a funny dragging noise
1 of 2 people found this instruction helpful.
  • Laurel from GODFREY, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Followed the instructions on the video. I was completely impressed because all the pictures on the video matched what I was looking at on the dryer. Very good job!!
Was this helpful?
Thank you for voting!
broken belt and idler pully
1 of 3 people found this instruction helpful.
  • vincent from staten island, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Thanks to the sep by step instructions I got from part select this repair was very simple. The disassembling was relatively easy, my new maintainance kit came the nest day, the machine was already apart and the parts went in without a hitch. THANKYOU
Was this helpful?
Thank you for voting!
Drum would not turn. Belt and pully were broke.
1 of 3 people found this instruction helpful.
  • Bradford from Marseilles, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I watched the video on the websit and it told me and showed me just what to do. Exccelent video, Ordered the repair kit, got it in two days. Job took me about 10 min.
Was this helpful?
Thank you for voting!
clothes dryer got hot, but stopped spinning
2 of 6 people found this instruction helpful.
  • diane from Miami, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
got my daughter's boyfriend over.. he is like McEiver.. can fix anything with a bobbypin.... he told me what to order, you delivered it in 2 days.. and the dryer was fixed the next day. All it cost me was a roast beef dinner
Much better than that repairman who would have charged a minimum of $100 plus parts... at probably triple y our cost...
Was this helpful?
Thank you for voting!
First squeaking, then something happened and would not run.
0 of 1 people found this instruction helpful.
  • Ernie from AVONDALE, AZ
  • Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers
Removed back panel to get to inside. Removed drum etc to replace drum rollers (ordered repair kit also), replaced the idler pulley etc, now like new. Repair successful!!!! Thank you!
Was this helpful?
Thank you for voting!
Gas dryer shut off mid cycle in timed cycle mode
3 of 11 people found this instruction helpful.
  • Brad from Wausau, WI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.
Was this helpful?
Thank you for voting!
All Instructions for the 110C68132413
106 - 120 of 211