- Home
- 110C68132413
- Instructions
110C68132413 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Tumbler drive belt was slipping which made grey dust coat inside of dryer
0 of 2 people
found this instruction helpful.
-
James from North Attleboro, MA
- Easy
- 15 - 30 mins
-
Screw drivers
Installed new belt and cleaned dust and wiped out inside of drum with Fantastic and clean sponge.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people
found this instruction helpful.
-
Howard from Boynton Beach, FL
- Easy
- 30 - 60 mins
-
Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol
... Read more
oring refer handles. Thank you
Read less
Was this helpful?
Thank you for voting!
Dryer Came On & Made Alot Of Noise
33 of 772 people
found this instruction helpful.
-
wendy from bush, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Took off the front of & lifted the top up. Pulled the drum out & replaced the two wheels that turn the drum, replaced the belt & replaced the pully wheel that turns the belt & dryer motor & put back together. The dryer now runs like a new one. Has no noise when running.
Was this helpful?
Thank you for voting!
Loud sqeaks, noise during drying.
-
Brian from Redmond, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
UNPLUG UNIT FIRST!!! Removed back cover. Make sure to note not all screws hold the back cover by closely observing the screw. Take a picture of the belt routing before removing from the idler pulley. Use headlamp or flashlight to light up pulley area. Remove belt from idler pulley by pushing idler assembly towards the right. Use smal
... Read more
l screwdriver to remove the existing pulley by prying off the existing tri-ring from the back of the pulley. You may have to "feel" the ring since it in facing away from you. Once tri-ring is removed, slide off old pulley and gasket or old second tri-ring. Replace with gasket first, then pulley then tri-ring. Reroute belt. Use picture if needed. Replace back cover.
Read less
Was this helpful?
Thank you for voting!
ice tray was broken
-
mike from fitchburg, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
This was by far so easy the instruction Partselect gave me where right on step by step. a repair man was going to charge 75$ just to come out 9$ from partselect. Thank you very much Mike chaplin
Was this helpful?
Thank you for voting!
Idler pulley bearings shot
-
Brian from Wakefield, NE
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Remove the back cover from the dryer after unplugging unit from electrical outlet. Remove the belt by moving tension arm. Remove the tension spring (by hand). Remove the idler pulley bracket with a nut driver. Remove the Tri-Star retaining clip with a screw driver. Remove the old idler pulley. Remove old washer... replace with new wa
... Read more
sher and idler pulley... I could have reused the tri star retaining clip but elected to use new one. Put arm back on, re-hook spring, realign belt, put back cover back on... dry clothes.
Read less
Was this helpful?
Thank you for voting!
The leveling foot on my dryer broke.
-
Diana from Clifton, NJ
- Really Easy
- Less than 15 mins
We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.
Was this helpful?
Thank you for voting!
Sqeaky Dryer
-
Mona from Vacaville, CA
- Easy
- Less than 15 mins
-
Screw drivers
My husband changed the idler pulley. It took him 5 min. Thank you sooooooooooo much. Saved us 1000.00 dollars. He wanted to by a new one but investigated the problem on line. He is a handyman and was just being lazy. I ordered the part and he fixed it. I love saving money!!!!!!!!!!!!! And I love my husband!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
My dryer had stop working and the terminal block, wires, and dryer plug burnt out
-
tiffanee from antioch, TN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers, Wrench set
I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. T
... Read more
hanks I hope the was useful.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
old idler pulley was worn out
-
David J from Eagar, AZ
- Easy
- Less than 15 mins
-
Nutdriver
Simply slid new idler wheel on then popped thr tri ring on. The belt replacment was the hardest thing which was also easy. I think pulling the dryer away from the wall was the most difficult thing.
Was this helpful?
Thank you for voting!
Drum not rotating
-
Chris from Sayrevlle, NJ
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Broken belt, but went with the mainentance kit since it was going to be all apart anyway. Found the job easy to do and the new belt idler was a big improvement over the old style. /also came with instructions. Good for another 5-10 years.
Was this helpful?
Thank you for voting!
Drum stopped turning
-
David from Jamestown, RI
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Using a stiff putty knife I depressed the clips that hold the top down. I loosened the screws at the lower edge of the front panel and removed the two 5/16 head screws that hold the front on. I unplugged the door switch and lifted the front off the lower screws. I removed the drum and the broken belt. I replaced the rear rollers after app
... Read more
lying some dry lube to the shafts and replaced the tension spring and rolled. I replaced the drum and belt and attached the belt to the small pulley on the motor. Then checked the rear gasket felt and reinstalled the front cover and the top.
Read less
Was this helpful?
Thank you for voting!
The dryer sounded like a herd of buffalos running by.
-
Patrick from Bettendorf, IA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I needed to replace our drum support rollers - one was completely worn out and wobbling (the buffalo herd noise) the other wasn't too bad, but for an older dryer(15+ years) I figured it was time to replace both wheels. I ordered the maintenance kit that also included the Idler Pulley and drum belt. I spent most of my time with the vacuum
... Read more
since there was a lot of dust accumulated inside the dryer. (I recoverd $1.83 in coins!) The instructions that came with the kit were very helpful for this repair. Plus, there were some online videos that heled as well. Once I had everything apart I noticed the plastic bearing ring on the drum's front was nearly worn out so I quickly ordered this from PartSelect and it arrived quicly in two days - this took only 10 minutes to replace.
Read less
Was this helpful?
Thank you for voting!
The Dryer would make a squealing noise like a toddler while running.
-
Ann from Phoenix, AZ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
We did repair by first watching a you tube video, then jumping in an dgoing step by step through the video. While not exactly the same dryer, the steps were in sequence. We thoroughly sleaned out the dryer with the tub out before reassembly. Th eonly slightly tricky part was putting front piece back, but once we mad esure ot align the
... Read more
sides for squareness the dryer went back together smoothly, execpt for one dropped screw. that was fished out through the bottom panel. The dryer runs quietly and we can watch TV with the door open to the laundry room again. I should have done this a long time ago. It started out by sqeaking at startup, then grew worse over time. I recomend anyone with a friend should be able to do this. Now with Cell phone pictures it is even easier to remember where the screw go.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
LOUD squeling from Dryer
-
John from Libertyville, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.
Was this helpful?
Thank you for voting!