110C60242510 Kenmore Dryer - Instructions

All Instructions for the 110C60242510
91 - 105 of 431

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Noisy while in use.
2 of 2 people found this instruction helpful.
  • Charles from ERIE, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.
Was this helpful?
Thank you for voting!
No heat
2 of 2 people found this instruction helpful.
  • Ronald from DRIPPING SPGS, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Replaced thermal sensors.
Was this helpful?
Thank you for voting!
Dryer was making a loud sound
2 of 2 people found this instruction helpful.
  • Frans from N ARLINGTON, NJ
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.
Was this helpful?
Thank you for voting!
No heat
2 of 2 people found this instruction helpful.
  • Doug from NEW BRAUNFELS, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Followed the video - easy!
Was this helpful?
Thank you for voting!
NO HEAT
3 of 5 people found this instruction helpful.
  • Larry from ARAB, AL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I highly recommend using a multi-meter to test for continuity on the thermistors and the heating element. It will likely save you a lot of time and you can replace the correct part the first time. I found the high limit thermostat to be open. Also note that if you find the same part open, it is most always caused by another part failure o r the dryer vent to be clogged up with lint. I also cleaned out the lint chamber which was in pretty bad shape and likely caused my failure. But, the parts were not expensive and were replaced while I was doing the trouble shooting. The video is excellent and if followed all will turn out ok. This is my third different appliance repair, and the parts are always in stock, the standard shipping was 7 days, and everything you need is provided.
Was this helpful?
Thank you for voting!
Loud screeching when dryer tumbles
2 of 2 people found this instruction helpful.
  • Joan from MANLIUS, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
We had to pop open the top. Unscrew front of dryer from sides. Disconnecting the wires was a bit more difficult than expected. We had to use a tiny screwdriver to slide into the sides of the white wire connector on each side before pulling apart. Front drum falls when front of dryer is removed. It took two of us to reassemble - one to hol d the drum while the other put the front on. Our problem turned out to be one wheel. We replaced both wheels and saved the rest of the parts. Hums along just fine.
Was this helpful?
Thank you for voting!
Tub bumping, shutting itself off after 20 minutes
2 of 2 people found this instruction helpful.
  • Kenneth from STONE MTN, GA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench set
Watched the videos available. Opened the top and saw tub jumping. Unplugged and removed front panel. Saw tub rollers were broken or melted. Removed tub watched more videos, and installed the felt belt I got from PartsSelect. Trouble removing the tub rollers, but finally got them off. The axles had a sticky residue which I removed wi th 220 grit sandpaper. I installed new rollers I had bought locally. Reassembled dryer. Worked quietly and smoothly, and it no longer shut itself down. Worked well for one day when it started.s loud noise with bumping. I found both rollers had lost their outer rim , and the tub was running on hard plastic and there was sticky residue back on the ankles. I stopped there.
Was this helpful?
Thank you for voting!
Will Not Tumber
3 of 6 people found this instruction helpful.
  • JOHN from PUNTA GORDA, FL
  • Really Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan
Was this helpful?
Thank you for voting!
Dryer tumbler made a loud noise
2 of 3 people found this instruction helpful.
  • jeff from albuquerque, NM
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this helpful?
Thank you for voting!
Blower flywheel needed replacement
2 of 3 people found this instruction helpful.
  • Gary from SAINT LOUIS, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
After watching the U Tube video to replace flywheel, I had a appliance repairman come to my home to install flywheel. There was no way I would have been able to put the dryer back together without some help.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while run ning around the house looking for the model number of the dryer.
Was this helpful?
Thank you for voting!
Worn bushing on bottom drum roller
3 of 6 people found this instruction helpful.
  • Frank from Avon, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mount ed new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).
Was this helpful?
Thank you for voting!
Broken dryer belt
3 of 6 people found this instruction helpful.
  • Mary from SCHENECTADY, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and ol d belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!
Was this helpful?
Thank you for voting!
Drum quit turning due to broken belt
3 of 6 people found this instruction helpful.
  • JENNIE from NORTH ROYALTON, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed the included instructions in the Maintenance kit. Very easy to understand & follow. Only advice is to have an extra set of hands to assist in re-installing drum w/ the new belt. Entire disassembly & reassembly could be done w/ basic hand tools but went alot quicker using a cordless drill w/ a set of nut/screw driver bits.
Was this helpful?
Thank you for voting!
drum support roller was squeaking VERY loud
2 of 3 people found this instruction helpful.
  • joe from southgate, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
Was this helpful?
Thank you for voting!
no heat from the dryer
2 of 3 people found this instruction helpful.
  • scott from missouri city, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
first i removed the back cover by removing the six 1/4 inch screws then i removed the wires to the thermal switch there were three of them and using an ohm meter i checked each one for continuity until i found the one that had an open circuit. i removed the two 1/4 inch screws holding it in place and replaced it with the new one.
Was this helpful?
Thank you for voting!
All Instructions for the 110C60242510
91 - 105 of 431