110C60242510 Kenmore Dryer - Instructions

All Instructions for the 110C60242510
121 - 135 of 431

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer ran but was not making heat
1 person found this instruction helpful.
  • Anne from GLEN COVE, NY
  • Very Easy
  • Less than 15 mins
  • Nutdriver, Pliers
followed the instructions on this site. to find the problem. checked the coil, thermostats and fuse with my multimeter. Found the bad one, order the part and put it in. It was very simple and now my 20 year old dryer works again.
Was this helpful?
Thank you for voting!
no heat
1 person found this instruction helpful.
  • james from ATLANTA, GA
  • Really Easy
  • Less than 15 mins
  • Socket set
still no heat.
Was this helpful?
Thank you for voting!
no heat only
1 person found this instruction helpful.
  • moujin from CARMEL, IN
  • Very Easy
  • Less than 15 mins
  • Nutdriver
repairing is pretty straightforward.
Was this helpful?
Thank you for voting!
Noise in dryer when dryer was turned on
2 of 4 people found this instruction helpful.
  • Michael from Marion, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.
Was this helpful?
Thank you for voting!
dryer would heat up once on a full hour cycle
1 person found this instruction helpful.
  • charles from waukesha, WI
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
i took a stab that it was the thermostat,but it wasn't.after finding out it was the coils i purchased them and lifted the top of the dryer and undid two screws in the upper front of the dryer and lifted the front off all while holding the tub in place.The coils are located in the very front left of the dryer,i took the holder bracket off, disconnected the wires and replaced the coils(they just sit on a rod)dryer works like new and thanks to the new thermostat also gets hotter,i'm guessing that was next.
Was this helpful?
Thank you for voting!
The Dryer would not heat up
1 person found this instruction helpful.
  • Rodger from DURYEA, PA
  • Easy
  • 15 - 30 mins
  • Socket set
I unplugged the machine and removed the back panel with a 1/4" socket. I unplugged each thermostat in turn and pulled them out. The internal bias was a bit tricky to remove without breaking the tabs or wires. I then placed each thermostat back in and replaced all the wires. Not bad at all. Weird thing is the dryer heats just fine now , until I put the back panel on; once I replace the back panel, it will not heat.
Was this helpful?
Thank you for voting!
Clothes taking too long to dry.
1 person found this instruction helpful.
  • Sherry from TUJUNGA, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
The dryer was igniting when initially starting load, but didn't light again the rest of the cycle. On my model the access was through the front panel, didn't even have to pull dryer out. Open the door and there are two screws on each side.of the inside of frame. Remove screws and lift door off the the whole front of the pulls out and d own and removes, and everything is right there to work on. Replaced thermostat, that took 5 min. But didn't fix the problem. So I purchased and replaced the "M" Series New Style Coil Kit, took about 10 min. I took olm/continuity readings b/t all terminals of the old and new coils and they were only about 5% difference, the old being a little lower. But that fixed the problem, works like new again.
Was this helpful?
Thank you for voting!
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
1 person found this instruction helpful.
  • Charles from Rupert, ID
  • Really Easy
  • 30 - 60 mins
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the dis charges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!

Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Was this helpful?
Thank you for voting!
Unit was tripping the circuit breaker after about 10 minutes of drying time
1 person found this instruction helpful.
  • Peter from FAIR OAKS, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged the unit, removed the back panel of the dryer and then removed the thermostat panel. Disconnected the wires on the thermostat and changed out the thermostat.
Was this helpful?
Thank you for voting!
The issue was I saw pieces of the felt in a load and all fell out a few days later Dryer started to make noce rotating once it got metal to metal stopped immedietly
1 person found this instruction helpful.
  • Katharine from PERRYSBURG, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Followed the video and stopped at each part not one issue very easy repair most difficult was separating the electric from from panel a little tricky to get apart.
Was this helpful?
Thank you for voting!
Dryer not heating, but motor running
1 person found this instruction helpful.
  • Dougls from Coconut Creek, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
I first unplugged the dryer and pulled it away from the wall. I had to remove the vent tubing to gain access to the rear of the unit, then removed the screws on the back panel of the dryer. I took off the panel and noticed that lint that had gathered over the years around the back of the dryer. I vacuumed it clean then proceeded to pr oblem solve. I noticed four easily identifiable areas, the thermal cut-off switch and thermostat located by the heating coil and the thermostat and fuse near the venting area. I first checked the fuse with a ohm meter, it was okay. I removed each component one at a time and created a bypass with a alligator clip wire. Plugged the dryer back in to determine if heat was produced while testing each area one at a time. I determined that heat was produced after bypassing the thermal cut-off switch. I then ordered the thermal cut-off switch kit (arrived within 3 days) and installed it within 20 minutes. The longest time spent was trouble shooting, the removal and installation was very easy. By the way, I did use the ohm meter to check the resistance across the thermostats as indicated in previous postings, but I found the results and technique to be more confusing. A bypass worked the best for me and much more reliable. The heat started immediately. I highly recommend downloading the schematics of your unit for part number and location identification.
Was this helpful?
Thank you for voting!
remove, take off , install
1 person found this instruction helpful.
  • jose from SANDY SPRINGS, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
just remove 4 screws removed the drum and put the affected part and that's it
Was this helpful?
Thank you for voting!
Pushing start button made buzzing sound but dryer didn't start.
1 person found this instruction helpful.
  • Jon from SIMI VALLEY, CA
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
The repair video provided for this model 110.97584810 gave erroneous info. It says to remove the back vent cover. The back on this model is not removable. I wasted an hour trying to remove back and top of dryer before discovering that the bottom front panel below the door pops off. Then the cover of the blower must be removed by removing two screws. The thermostat part can then be accessed and replaced as shown in the video. You'll need a 1/4" rachet to remove the screws as there isn't space to use a nut driver. Note that the statement in the video "This repair is done all from the back" is completely wrong. It is done entirely from the front. It can be done without even moving the dryer.
Was this helpful?
Thank you for voting!
Dryer was making loud noises.
1 person found this instruction helpful.
  • Larry from PHILADELPHIA, PA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.
Was this helpful?
Thank you for voting!
Dryer was making bad noises like a bearing was going out, then it got worse and sounded really loud, so I couldn't even run it.
1 person found this instruction helpful.
  • Margo from FOX ISLAND, WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed the instructions found online. Only thing I would add is that the clips are easier to work with if you warm them up a little before you try to install them.
Was this helpful?
Thank you for voting!
All Instructions for the 110C60242510
121 - 135 of 431