110C60242510 Kenmore Dryer - Instructions

All Instructions for the 110C60242510
106 - 120 of 431

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
dryer was not heating anymore
2 of 3 people found this instruction helpful.
  • Audrey from North Miami, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
removed the back housing of the dryer and located the thermal switch. unscrewed the old one, popped in the new one and whala! I was back in business!

put the back cover back on the dryer and pushed it back into place.
Was this helpful?
Thank you for voting!
taking to long to dry
2 of 3 people found this instruction helpful.
  • John from BEAVERCREEK, OH
  • Really Easy
  • 15 - 30 mins
put the high limit in , plus the temperature , plus the exhaust switches
Was this helpful?
Thank you for voting!
Loud noise while in use
2 of 3 people found this instruction helpful.
  • Josh from Madill, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!
The dryer tub became jammed, unable to turn.
3 of 6 people found this instruction helpful.
  • Terry from Lindsay, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.
Was this helpful?
Thank you for voting!
Fan blade had to be removed , was broken off from motor.
2 of 3 people found this instruction helpful.
  • James from Colorado Springs, CO
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
Was this helpful?
Thank you for voting!
noisy dryer
1 person found this instruction helpful.
  • Thomas from MYRTLE BEACH, SC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
followed the enclosed instructions, used a balled up towel to support the drum while attaching the belt and tension pulley, took about 20 minutes
Was this helpful?
Thank you for voting!
Clothes never completely dry
1 person found this instruction helpful.
  • Ed from GRAFTON, IL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I watched the video then called them to order parts. They were VERY helpful & NICE. I had the parts the NEXT day. I followed the video instructions & it worked. They made my day! THANK YOU JoAnn & Teresa!
Was this helpful?
Thank you for voting!
Belt
1 person found this instruction helpful.
  • MARY from PORT ALLEN, LA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
My son did the repairs it took less than 30 minutes it's an old dryer so glad to be able to get the parts. I do not like the new dryers because of all the pushbuttons thanks so much for the ports
Was this helpful?
Thank you for voting!
Dryer would not heat on any heat settings.
1 person found this instruction helpful.
  • Larold from WILLMAR, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
First I watched the repair video on-line at this site After pulling the dryer away from the wall and unplugging the 220 volt power cord I removed the back panel with the 9 screws. I then unplugged the wires to the thermostat/heating element. With an ohm meter I discovered that the heating element was good and the high limit thermostat w as bad. I ordered the high limit thermostat from this site on a 2 day shipment. When the part arrived I installed the part and the wires. Plugged in the dryer for a quick check for heating. Replaced the back panel and moved the dryer back into position. Dryer works fine now.
Was this helpful?
Thank you for voting!
Dryer wasn't getting real hot and took a few cycles to dry.
1 person found this instruction helpful.
  • Steve from WOODLAND HLS, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Thank goodness the part was still available for a 25 year old dryer. Website was great to help solve the problem and the video was wonderful to show me how to identify the part and how to get to it. You take off the back of the dryer and then unscrew the thermostat from it's mooring. Undo the 4 wire connections. Stick in the new therm ostat and re-install. Thank you!
Was this helpful?
Thank you for voting!
I had only seen a one piece rack .The 2 piece threw me for a loop.
1 person found this instruction helpful.
  • Keith from Shawnee, KS
  • Easy
  • 15 - 30 mins
I thought I had checked the arm piece of the rack real good for a product number on my original part but I missed the number till the 2nd box came in, and a looked real careful and realized it was the same as the order I thought was bad.
Put the spring arm in first and the rack will fit in the front groove.
It would have bee n good if there had been a picture of the dryer arm attached to the dryer.
So I have 2 good racks and will return one if you tell me where to send it.
Keith Walden..
Was this helpful?
Thank you for voting!
dryer want heat up
1 person found this instruction helpful.
  • sheldon from macon, GA
  • Really Easy
  • 15 - 30 mins
  • Socket set
they sent the wrong part . when i got the right part i removed the two screws holding the element . took the Thermostat out . removed the plugs . put the new thermostat in plug in the plugs. screwed the element back in place . And now i need to replace the fuse located at the top of the element casing.
Was this helpful?
Thank you for voting!
Dryer wouldn't heat
2 of 4 people found this instruction helpful.
  • Kendahl from Leander, TX
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
I shorted the thermal cutout after removing the back.
I then ordered the thermal Cut-Off Kit from PartSelect.
While this was not my first order from them, I was still impressed with the ease and by how soon I received the part without any hassles or glitches. PartSelect will be my primary parts supplier from now on.
Was this helpful?
Thank you for voting!
The thermo cut off is dead.
1 person found this instruction helpful.
  • moua from FRESNO, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I bought a new thermo cut off and replaced the old one.
Was this helpful?
Thank you for voting!
Dryer would not heat
1 person found this instruction helpful.
  • Enrique from LA VERGNE, TN
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Looked on YouTube and found these guys. Followed their instructions and no problem.
Was this helpful?
Thank you for voting!
All Instructions for the 110C60242510
106 - 120 of 431