- Home
- 110C60242510
- Instructions
110C60242510 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer runs, but won't heat.
4 of 4 people
found this instruction helpful.
-
Eric from DELHI, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
First only replaced the high temp cut off switch which allowed the element to heat. However, after one heat cycle the switch would not reset. Then changed the thermostat (included in the kit). After tapping the cut off switch lightly to manually reset it, the dryer ran perfectly. Moral of the story: always change all parts included with a
... Read more
repair kit!
Read less
Was this helpful?
Thank you for voting!
Noisy when drum rotates
4 of 4 people
found this instruction helpful.
-
lance from GREENSBURG, PA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.
Was this helpful?
Thank you for voting!
drum roller became lose and seperated from the shaft that supports it. it had to be replaced
5 of 7 people
found this instruction helpful.
-
Dillard C. from Vina, AL
- Easy
- 15 - 30 mins
-
Socket set
remove the front panel, belt [notice the way the belt is fasten] remove the tub, support bracket to the drum roller, and slide the new drum roller on and place the tre ring in the slot. then re-install everything in reverse
Other Parts Used:
Was this helpful?
Thank you for voting!
No Heat
4 of 5 people
found this instruction helpful.
-
Richard from Eaton, OH
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
The dryer stopped heating, it would only blow cold air. I removed the back panel and tested the thermal fuse with a dmm. The fuse was open, so it was bad and I needed a new one. I tested the thermostat and the dmm measured continuity across the terminals, so I thought it was good, bad assumption. I ordered a thermal fuse from part
... Read more
sselect and it came with a thermostat. Like a dummy, I only installed the fuse. The 1st time I ran the dryer the fuse blew again, because the thermostat was bad. So, moral of the story, install both parts.
Read less
Was this helpful?
Thank you for voting!
Broken belt
4 of 6 people
found this instruction helpful.
-
Mark from MILFORD, CT
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
As seen in video, All Good !
Was this helpful?
Thank you for voting!
dryer not hot enough, too long to dry.
3 of 3 people
found this instruction helpful.
-
Willis from GRAND FORKS, ND
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Installed thermal cut-off kit. Dryer works fine now. Kit very easy to install.
Was this helpful?
Thank you for voting!
dryer would work, didn't have any heat.
3 of 3 people
found this instruction helpful.
-
linda from buckeye, AZ
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
unpluged the dryer, took off the back, followed instructions and was able to take of the problem on my own.
Was this helpful?
Thank you for voting!
Machine was in need of new Thermostats
5 of 9 people
found this instruction helpful.
-
KELVIN from DISTRICT HEIGHTS, MD
- Really Easy
- 15 - 30 mins
-
Nutdriver
I did my repair alone by myself after viewing a short video online at partselect.com The man in the video showed every step slowly and professionally. I took some extra time to clean the dust off behind the back of Dryer while I had it open for fixing.....thanks for your help and it saved me over $190 plus which I was quoted by technici
... Read more
an for estimate and parts. I paid $43.00 for my parts...both High limit and Cycling thermostats were replaced. My wife told me good job honey ! You can do it too.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people
found this instruction helpful.
-
David from JOLIET, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
broken blower wheel
3 of 3 people
found this instruction helpful.
-
Vern from NEWBERG, OR
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people
found this instruction helpful.
-
Craig from VASS, NC
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Other Parts Used:
Was this helpful?
Thank you for voting!
the lower drum support roller had been chewed to bits.
3 of 4 people
found this instruction helpful.
-
Rodney from Mt. Jackson, VA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with
... Read more
wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
Read less
Was this helpful?
Thank you for voting!
Dryer heating up but clothes not drying
3 of 4 people
found this instruction helpful.
-
Donald from Knoxville, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.
Other Parts Used:
Was this helpful?
Thank you for voting!
Terrible noise coming from the rotation of drum
3 of 4 people
found this instruction helpful.
-
Leo from MERIDIAN, ID
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waite
... Read more
d 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start
3 of 4 people
found this instruction helpful.
-
Gary from East Durham, NY
- Really Easy
- 15 - 30 mins
-
Socket set
I put in the new parts but it still did not work, Turned out the Thermal Fuse Blew,removed the two wires and clipped them together and the Dryer worked, have to replace the Thermal fuse and everything will be OK.
Other Parts Used:
Was this helpful?
Thank you for voting!