- Home
- 110C60242510
- Instructions
110C60242510 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Loud rumble noise while drum was turning
9 of 12 people
found this instruction helpful.
-
Marcia from CAmden, NY
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
First I pulled out lint catcher, you will see two screws ,removed two the screws on top ,( philips head screw driver) I than took a putty knife and pushed in the front of the dryer under the lid and lifted the top up, I than removed a self tapping screw on each side with a 5/16 wrench and lifted the front panel out. I than pulled out the
... Read more
drum and this exposed the two rollers, I than pulled of the nut locks with athe pliers , took off the plastic triangle snaps and pullled off the old rollers , replaceing them with the new ones,put the triangle locks on and that the lock nuts on , I than put the drum back in, than the front panel, replaceing the two self tapping screws , snapped down the top,replaced the other two screws again on top and replaced the lint catcher, I was done.
Read less
Was this helpful?
Thank you for voting!
Lost bearing on dryer motor
9 of 13 people
found this instruction helpful.
-
John from Wilmington, OH
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I looked at the parts breakdown to see how it cam apart.
I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is ... Read more the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.
I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is ... Read more the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.
Read less
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people
found this instruction helpful.
-
Joseph from Austin, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t
... Read more
o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Read less
Was this helpful?
Thank you for voting!
Dryer air would not heat
7 of 8 people
found this instruction helpful.
-
Jacqulyn from ANDERSON, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Boyfriend stated it was simple, he removed the back and replaced the part using a few everyday tools.
Other Parts Used:
Was this helpful?
Thank you for voting!
Loud Noise While Drying
7 of 9 people
found this instruction helpful.
-
John from Metamora, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!
john
john
Was this helpful?
Thank you for voting!
Dryer making a rumbling sound
8 of 13 people
found this instruction helpful.
-
Michael from Jacksonville, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.
Was this helpful?
Thank you for voting!
drum stopped rotating - broken belt
7 of 10 people
found this instruction helpful.
-
lisa from manteca, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Super easy to repair...I had to idea how to get started; but after watching the video from your site it was a breeze. Thanks for having "how to repair" videos on your site.
Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new
Repair kit came in 2 days..fantastic..thank you so much....with new rollers, belt and tension roller she works like new
Was this helpful?
Thank you for voting!
Loud, low-pitched thumping noise
7 of 10 people
found this instruction helpful.
-
Joseph from SKANEATELES, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First, let me say the t videos are excellent. Check them out if you haven't already.
I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.
I took a chance and ordered the maintenance kit to avoid having to take the dryer part ... Read more to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .
Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.
Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.
As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.
It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.
One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)
It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.
I came across the video on diagnosing the causes of odd dryer noises. After watching that, I decided that the issue was probably a drum roller.
I took a chance and ordered the maintenance kit to avoid having to take the dryer part ... Read more to confirm the diagnosis and then put it back together again while waiting for the parts to arrive (BTW - the parts arrived within two days of my ordering them) .
Even if you know your issue is only the roller, I recommend getting the entire kit. It takes no extra time to replace the drive belt and the idler pulley while you have to dryer apart and I consider it good preventative maintenance.
Definitely watch the how-to video PartSelect provides on how to perform the repair using the maintenance kit. It's very clear and very helpful. I'm not sure I could have figured out how the belt fit through the idler pulley without it.
As video shows, the repair is pretty straightforward. As others have noted, you'll likely find a couple of dollars in change and a goodly layer of lint in the bottom of the cabinet. Have your shop back handy.
It seems kind of silly, but I found the hardest part of the whole repair was getting the front panel to slide onto the two bottom clips that support it.
One thing to watch out for are two small metal clips surrounding the screw holes at the top of the front panel. The nut screws that hold the panel in place screw into these, not the panel itself. After I struggled to get the panel in place I realized that in the process I had knocked the clips off and so had to remove the front panel again in order to retrieve the clips from the bottom of the cabinet. Minor frustration. And with all the practice I had the first time around, the panel went on much more easily the second time :-)
It was very gratifying to plug the dryer in, turn it on and have it run perfectly. Better yet, it impressed my wife.
Read less
Was this helpful?
Thank you for voting!
Poor drying and took excessive amount of time to complete partially dried loads
5 of 5 people
found this instruction helpful.
-
Stephen from LOUISVILLE, KY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.
Other Parts Used:
Was this helpful?
Thank you for voting!
Belt broke
6 of 8 people
found this instruction helpful.
-
Thomas from Okemos, MI
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Perfect!
Was this helpful?
Thank you for voting!
Motor was bad
5 of 5 people
found this instruction helpful.
-
Michael from CLIFTON HTS, PA
- Really Easy
- 30 - 60 mins
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part s
... Read more
o I can redo a testimonial here for you. 19 days and still waiting
Read less
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people
found this instruction helpful.
-
Betty from Erie, PA
- Really Easy
- 15 - 30 mins
-
Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
incessantly annoyingly squeaky dryer
5 of 6 people
found this instruction helpful.
-
Douglas from Tiburon, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an
... Read more
d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Read less
Was this helpful?
Thank you for voting!
Dryer quit heating
6 of 9 people
found this instruction helpful.
-
Christopher from Orlando, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I removed the hex head screws from the back of the dryer and removed the back panel, after unplugging the dryer. I tested the various electrical components until I found that the upper limit temp fuse had gone out. Came to partselect.com and found the kit I needed and ordered it. When it came in, I replaced the upper temp limit fuse, a
... Read more
nd the other parts that came with the kit. I also, since the back was open, used the opportunity to vacuum out the blower fan and as much of the lint as I could get to. Dryer works great now!
Read less
Was this helpful?
Thank you for voting!
The dryer was squeaking and would not heat at all.
7 of 12 people
found this instruction helpful.
-
Steven from Oxnard, CA
- Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The first thing I did was call my friend Donnie who manages some apartment buildings and who is always complaining about fixing things and getting the right parts to fix things. He told me what to order from PartsSelect and when the parts got here I called him up and he did the repair work.
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
He was reluctant to do the work at f ... Read more irst but after he found out I had ordered the parts from PartsSelect he was happy to do the work. "Their parts are always right and they always work," was what he said after he had my dryer working just like new. So if you know nothing about fixing things and buying parts just call PartsSelect and you will be fine. Just ask my friend Donnie!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!