1106705 Kenmore - Instructions

All Instructions for the 1106705
91 - 105 of 249

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
Loud squeaking noise
3 of 4 people found this instruction helpful.
  • Steven from WICHITA, KS
  • Really Easy
  • 30 - 60 mins
  • Pliers
Replaced the most worn drum wheel any lubed the belt tension arm pulley. The noise didn't go completely away. There are 4 drum wheels. I need to order 3 more wheels and the tension arm now.
Was this helpful?
Thank you for voting!
Dryer won’t start
3 of 4 people found this instruction helpful.
  • Kyle from HANOVER, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Drum belt broke. Found drive shaft belt guide broke. Replaced pulley wheel since I had it apart.
Was this helpful?
Thank you for voting!
Dryer not heating
2 of 2 people found this instruction helpful.
  • James from GREENVILLE, NC
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Confirmed I had incoming 240V, checked continuity on element switch confirmed bad. Ordered replacement part. U have to remove drum to replace element
Was this helpful?
Thank you for voting!
Lights turn on, all the beeps but dryer won't start.
2 of 2 people found this instruction helpful.
  • James from HONESDALE, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I ordered the wrong part. It was pick and choose from the info provided.I checked again and found one that's 58% of the time the part.
Was this helpful?
Thank you for voting!
Broken dryer belt and broken idler pulley wheel
3 of 5 people found this instruction helpful.
  • ROGER from MADISON, TN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Looked it up on YouTube and followed the video instructions. Repair went fine after I got the correct parts ordered from two different places before I got the correct parts. Parts Select was the only one that sent the correct parts.
Was this helpful?
Thank you for voting!
Shutting off and had to wait before could turn back on
2 of 2 people found this instruction helpful.
  • Allen from KENNETT, MO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Followed online video very easy and dryer works like new one....
Was this helpful?
Thank you for voting!
Heater element had burnt open and would not heat.
2 of 2 people found this instruction helpful.
  • Joe from COWARD, SC
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
I found a simple video on YouTube. I removed the front panel and door. I removed drum and belt drive. Heater element was then easily accessible. I removed all wires after taking pictures of wiring. Element was secured by one screw and one clip and was easily removed. Removed element from element cover. Checked thermostat and thermal overl oad. Put new element inside of element cover. Then replaced everything in reverse order. Removing lint from inside of dryer was probably the most difficult part of repair. Had to have assistance from my son to put drum belt back on but rest of replacement was simple.
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people found this instruction helpful.
  • Carl from MARION, KY
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!
Electric Heating Element went out.
2 of 2 people found this instruction helpful.
  • John from WELLS, MN
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers, Socket set
I checked continuity of all electrical points. I took the top off, then the back, and front of the dryer off so it was easy to inspect the whole dryer. I was also able to clean unwanted dust, and lent with a shop vacuum by doing this.
Keep track of different screws, and mark each screw location with a permanent magic marker. Taking pictures with camera phone is very helpful. Pay attention to electrical connections as well, some of those will need to be dismantled.
Try not to take apart anything more than needed. Watching some online video's can be very helpful as well.
If uncomfortable doing this, call a service repair technician.
I'm a farm boy, and repairs usually come easy to me, but not always.
Was this helpful?
Thank you for voting!
No leveling feet on dryer.
2 of 2 people found this instruction helpful.
  • Bobbie from BEND, OR
  • Very Easy
  • Less than 15 mins
  • Wrench (Adjustable)
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Was this helpful?
Thank you for voting!
The door catch no longer held the door shut. It would not grip the bayonet.
2 of 2 people found this instruction helpful.
  • Douglass from Madison, IN
  • Very Easy
  • Less than 15 mins
  • Pliers
The only challenging part was getting the old catch out. It can easily fall inside the door, not that this is really a problem, just leave it there. Using pliers get a good grip on the edge of the old catch and rock the top out, then pull to get the bottom out. There will now be an open hole. Align the new part with the open hole, and sim ply push it in. It will catch, and click into place. No tools are needed to install.
Was this helpful?
Thank you for voting!
The Dryer door catch broke and the door would not latch.
2 of 2 people found this instruction helpful.
  • Douglas from LINCOLN, NE
  • Really Easy
  • Less than 15 mins
  • Pliers
I removed the broken door catch with a screw driver. I then used a pair of pliers to push the new door catch in place. It was an easy repair and saved me quite a bit of money.
Was this helpful?
Thank you for voting!
lint screen was not catching lint and sending out the dryer vent
2 of 2 people found this instruction helpful.
  • Scott from WOODBURY, MN
  • Very Easy
  • Less than 15 mins
replaced dryer lint screen with new.
Was this helpful?
Thank you for voting!
Door switch had failed. Dryer would not start.
3 of 5 people found this instruction helpful.
  • dan from Melbourne, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Opened front of dryer and replaced switch.
Best part was ordering and receiving switch in two days. You guys really do ship the same day as ordered.
Was this helpful?
Thank you for voting!
All Instructions for the 1106705
91 - 105 of 249