1106705 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Squealing pulley
6 of 8 people
found this instruction helpful.
-
Randall from MILLSAP, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Socket set
Removed rear cover. Released tension on spring to pulley to remove belt from pulley. Used a socket to remove idler. Did the reverse to install.
Was this helpful?
Thank you for voting!
Dryer would not heat
5 of 5 people
found this instruction helpful.
-
GARY from PARSONS, KS
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the p
... Read more
arts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.
Read less
Was this helpful?
Thank you for voting!
Door would not close after I slammed it.
5 of 5 people
found this instruction helpful.
-
Jeffrey from FRANKLIN, MA
- Really Easy
- 30 - 60 mins
Simple with the Instructions in the video.
Other Parts Used:
Was this helpful?
Thank you for voting!
Very noisy from support wheels
7 of 12 people
found this instruction helpful.
-
Steven from WICHITA, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Changed all 4 drum support wheels and belt tension arm
Other Parts Used:
Was this helpful?
Thank you for voting!
door would not latch
4 of 4 people
found this instruction helpful.
-
Paul from BENTONVILLE, AR
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
removed old latch with pliers - inserted new latch
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people
found this instruction helpful.
-
Paul from STONE CREEK, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Blower belt came loose, but didn't snap. It was old and perhaps brittle.
4 of 4 people
found this instruction helpful.
-
Gabe from Tulsa, OK
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
First, lift top by pushing in the 2 locking clips ( with the dryer door open), otherwise it won't lift.
Secondly, remove front cover by taking out 2 screws easily seen . If you see any electrical connectors, remove them.
Only thing a bit nightmarish was installing the new belt. It didn't seem long enough even though it was the ... Read more original exact replacement. I got hair dryer blower, used on belt for 30 seconds, and mission accomplished.
Secondly, remove front cover by taking out 2 screws easily seen . If you see any electrical connectors, remove them.
Only thing a bit nightmarish was installing the new belt. It didn't seem long enough even though it was the ... Read more original exact replacement. I got hair dryer blower, used on belt for 30 seconds, and mission accomplished.
Read less
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people
found this instruction helpful.
-
Gregory from COCOA, FL
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
dryer making noise. order parts
4 of 6 people
found this instruction helpful.
-
Thomas from TULELAKE, CA
- Very Difficult
- 30 - 60 mins
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
Read less
Was this helpful?
Thank you for voting!
Clothes were not drying on auto sensor.
3 of 3 people
found this instruction helpful.
-
Michael from Annapolis, MD
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people
found this instruction helpful.
-
Helen from NASHUA, NH
- Really Easy
- 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
YouTube video dated 9/28/2015
3 of 3 people
found this instruction helpful.
-
Madeline from PANA, IL
- Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.
Was this helpful?
Thank you for voting!
Dryer would not start, showed F40 code
3 of 3 people
found this instruction helpful.
-
Glenn from KINGSPORT, TN
- Really Easy
- 30 - 60 mins
-
Nutdriver
Very easy do it yourself repair, and saved at least $300.00. I watched a video and it took me less than 20 minutes to complete repair. Part fit perfect and I have already ordered another to keep as a spare.
Was this helpful?
Thank you for voting!
Blower stopped working
3 of 3 people
found this instruction helpful.
-
Boots from KNOXVILLE, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I expected to find a broken blower belt so purchased that belt and the others I planned to replace since the on line instructions indicated that I had to pull the drum to replace the blower belt. I did not, so didn't use most of the parts at all. The instructions that came with the parts, were only slightly helpful because they were for a
... Read more
far different model. Some youtube videos were more help. I had to pop the top, which is easy and explained in the instructions, remove the front panel, which only requires removing two 5/16" small bolts, then lifting it up and off. Simple. With that panel off, I could see the blower belt and it was intact and seemed to work fine. I could have replaced it easily with no further disassembly at that point. However, since it was not blowing the air out of the dryer, I knew there was another problem. So I removed the front of the blower housing, which is four, 1/4" small bolts and it just pulls off. I could then see that the entire front of the blower was packed with lint that had gotten past the normal lint filter. I cleared that all out and checked that the blower itself was intact and clean and there were no other obstructions. When I rotated the blower by turning the motor, it moved easily. So I put it all back together without changing any parts and tested it. It worked perfectly again. I kept the parts for the next time I might need them.
Read less
Was this helpful?
Thank you for voting!
Dryer would squeal when the drum was turning
3 of 3 people
found this instruction helpful.
-
Clinton from MINOOKA, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I followed the very informative video and wrote down step-by-step notes for myself. The repair went very smoothly. The only thing I didn't realize, was that the dryer has 4 rollers, not just 2 shown in the video. All are easy to access once you disassemble. I had to do it twice since I had to order 2 more rollers in order to replace t
... Read more
hem all. Also, the triangle plastic washers come with the roller, so you won't need to order them separately like I did. I also changed the idler pulley roller while I was in there since that has bearings too. Just as easy. I'm very happy with my quiet dryer! One last note: The new rollers are a bit louder than normal at first, but they quiet down very quickly as you use the dryer. It must be because they are brand new.
Read less
Was this helpful?
Thank you for voting!