1106705 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door catch will no longer secure the door close
6 of 6 people
found this instruction helpful.
-
Gregory from Carlsbad, CA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pliers and screw driver to pop out the old door catch and pop in the new one. Saved $69.95 service charge for a tech to come to the home.
Was this helpful?
Thank you for voting!
Heating element went out
6 of 6 people
found this instruction helpful.
-
Chris from CANON CITY, CO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I watched your instruction video, which by the way, 1. was not for my model dryer and 2. was totally opposite of what you showed. I was able to remove the back and replace it from there versus going in from the front and removing the drum, etc etc
Was this helpful?
Thank you for voting!
Dryer does not heat but blows only cold air
6 of 6 people
found this instruction helpful.
-
kevin from RENTON, WA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch
Was this helpful?
Thank you for voting!
Felt that lines the edges of the drum had degraded from the side nearest the door.
6 of 6 people
found this instruction helpful.
-
Chris from DAYTON, OH
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
I was not able to find a video (or other specific instructions) that showed how to access the insides of this particular machine, but eventually figured out that all it takes is popping 2 clips, one on either side of the door by wedging a flathead screwdriver in the space between the top of the machine and the bottom piece that surrounds
... Read more
the door opening. The top then pivots up and can be moved back beyond vertical so that it hold itself in position.
After removing the dryer door, getting to the drum itself was not too difficult and only involves removing half a dozen small bolts. I was able to move the pieces off to the side without disconnecting any of the wiring. Without looking at the parts diagram I can't name any of the pieces involved, but there were only a couple. The drum can then be lifted right off its rollers.
The replacement felt for this dryer has to be fastened with adhesive, and I would recommend running the bead of glue around half of the drum, setting the new felt in place, letting it sit for a few minutes to let the glue set up, then repeating for the other half. I tried installing the entire piece of felt at once, but after getting about 3/4 of it on, pulling the remaining unattached felt taut to fit around the drum ended up removing the first part of the felt because the glue did not have time to set up. If you've ever changed a bicycle tire, you'll know about reaching that point where the tire doesn't seem big enough to fit around the rim, but it just needs to be muscled into place. Same idea here, but trying to muscle the felt over fresh glue while the just installed part comes loose is frustrating and in my case almost resulted in ruining the entire new felt strip. Once the felt is anchored it's easy to pull taut over the remaining part of the drum.
After removing the dryer door, getting to the drum itself was not too difficult and only involves removing half a dozen small bolts. I was able to move the pieces off to the side without disconnecting any of the wiring. Without looking at the parts diagram I can't name any of the pieces involved, but there were only a couple. The drum can then be lifted right off its rollers.
The replacement felt for this dryer has to be fastened with adhesive, and I would recommend running the bead of glue around half of the drum, setting the new felt in place, letting it sit for a few minutes to let the glue set up, then repeating for the other half. I tried installing the entire piece of felt at once, but after getting about 3/4 of it on, pulling the remaining unattached felt taut to fit around the drum ended up removing the first part of the felt because the glue did not have time to set up. If you've ever changed a bicycle tire, you'll know about reaching that point where the tire doesn't seem big enough to fit around the rim, but it just needs to be muscled into place. Same idea here, but trying to muscle the felt over fresh glue while the just installed part comes loose is frustrating and in my case almost resulted in ruining the entire new felt strip. Once the felt is anchored it's easy to pull taut over the remaining part of the drum.
Read less
Was this helpful?
Thank you for voting!
Idler pulley squeaking very badly
6 of 6 people
found this instruction helpful.
-
Andy from DAGGETT, MI
- Really Easy
- 30 - 60 mins
-
Socket set
Took back panel of dryer off completely disconnected the drive belt to drum of dryer took off old idler pulley reinstall the new pulley and belt works like a brand new dryer
Was this helpful?
Thank you for voting!
The middle tub would not come out
7 of 9 people
found this instruction helpful.
-
Jayanti from SNELLVILLE, GA
- Very Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , ... Read more I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job
Read less
Was this helpful?
Thank you for voting!
High pitch noice
8 of 13 people
found this instruction helpful.
-
Luis from FRESNO, CA
- Easy
- 30 - 60 mins
-
Pliers, Socket set
Raised the front of top panel with the putty knife and the front panel was unscrewed as the video showed. The drum slid out after the belt was released.
My machine had 4 rollers, which was not shown in the schematics. So I replaced the back, cleaned the front ones and works great for now. Plan to replace the front later.
... Read more />
Removing the tri rings is much easier if cut w wire cutters. Otherwise waist lots of time to get them off. Just buy new ones.
My machine had 4 rollers, which was not shown in the schematics. So I replaced the back, cleaned the front ones and works great for now. Plan to replace the front later.
... Read more />
Removing the tri rings is much easier if cut w wire cutters. Otherwise waist lots of time to get them off. Just buy new ones.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the factory door catch punched out
8 of 13 people
found this instruction helpful.
-
phillip from evansville, IN
- Really Easy
- Less than 15 mins
new part came in a day or two. took part out of package and it easly snaped in place. very nice
Was this helpful?
Thank you for voting!
Old lint filter was broken
8 of 14 people
found this instruction helpful.
-
Earl from Santa Ana, CA
- Really Easy
- Less than 15 mins
Just replaced the old lint filter.
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people
found this instruction helpful.
-
Betty from Erie, PA
- Really Easy
- 15 - 30 mins
-
Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
Dryer Top Panel is Loose
5 of 5 people
found this instruction helpful.
-
MONTE from CHESAPEAKE, VA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each ... Read more locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each ... Read more locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
Read less
Was this helpful?
Thank you for voting!
Lint filter seal worn out
5 of 5 people
found this instruction helpful.
-
Dennis from PALM BCH GDNS, FL
- Very Easy
- Less than 15 mins
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this helpful?
Thank you for voting!
Drum support roller making very loud noise
5 of 5 people
found this instruction helpful.
-
William from TROY, AL
- Really Easy
- 1- 2 hours
-
Screw drivers, Socket set
had to take front off of Dryer then was able to replace drum roller
Other Parts Used:
Was this helpful?
Thank you for voting!
idler pulley wheel was bad
5 of 5 people
found this instruction helpful.
-
Jasper from FLORIEN, LA
- Very Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
Simply removed back cover on dryer and the idler pulley wheel and arm was right there and only had one screw to remove after relieving tension on belt by removing spring. Very simple
Was this helpful?
Thank you for voting!
1`) broken blower motor drive belt,2) blower moter drive belt pulley loosened & seperated from shaft
5 of 5 people
found this instruction helpful.
-
Tim from DUNCANVILLE, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
1) Unplugged unit & used the 5 in 1 tool to disengage top panel clips from top of front panel & tilted top panel up & out of the way, .
2) Disconnected electrical connection @ upper right of front panel, Used drill & 5/16" socket & adapter to remove 2 upper front panel screws on backside of panel & removed panel.
3) Removed 4 sc ... Read more rews from lint screen duct, unplugged elect. con.@ the right & removed lint screen & duct from dryer bulkhead..
4) Loosened 2 top screws & removed 2 bottom screws from bulkhead & lifted bulkhead up & out & set aside.
5) Slid drum belt off the back of the drum & removed the drum
6) Ceaned the blower moter drive shaft threads & threads inside the shaft pulley. Used a file to clean up any burrs on shaft pulley, coated treads of pulley & shaft with red lock tite thread dressing & re-instaled pulley back onto shaft with ajustable pliers while holding blower fan blades steady from inside the blower motor housing. with other hand. note: (pulley is left handed thread)
7) Looped new belt onto drive motor pulley then worked it back onto blower moter pulley with one hand while turning the blades of the blower from inside the blower housing with other hand until it was back in place & ribs on belt were seated in the mating ribs of the pulley.
8) Put everything back in reverse order with the exception of removing the back panel to reinstall the drum belt onto the drive motor shaft pulley and tensioner @ bottom left in back of the dryer.
Hope this instructional is able to help some one else & good luck with your projects!
2) Disconnected electrical connection @ upper right of front panel, Used drill & 5/16" socket & adapter to remove 2 upper front panel screws on backside of panel & removed panel.
3) Removed 4 sc ... Read more rews from lint screen duct, unplugged elect. con.@ the right & removed lint screen & duct from dryer bulkhead..
4) Loosened 2 top screws & removed 2 bottom screws from bulkhead & lifted bulkhead up & out & set aside.
5) Slid drum belt off the back of the drum & removed the drum
6) Ceaned the blower moter drive shaft threads & threads inside the shaft pulley. Used a file to clean up any burrs on shaft pulley, coated treads of pulley & shaft with red lock tite thread dressing & re-instaled pulley back onto shaft with ajustable pliers while holding blower fan blades steady from inside the blower motor housing. with other hand. note: (pulley is left handed thread)
7) Looped new belt onto drive motor pulley then worked it back onto blower moter pulley with one hand while turning the blades of the blower from inside the blower housing with other hand until it was back in place & ribs on belt were seated in the mating ribs of the pulley.
8) Put everything back in reverse order with the exception of removing the back panel to reinstall the drum belt onto the drive motor shaft pulley and tensioner @ bottom left in back of the dryer.
Hope this instructional is able to help some one else & good luck with your projects!
Read less
Was this helpful?
Thank you for voting!