1106705 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The washing machine was leaking.
3 of 3 people
found this instruction helpful.
-
Matthew from Affton, MO
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I followed the provided video for changing the centerpost gasket.
I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.
If a man is somewhat handy, this is a doable ... Read more repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.
It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.
I successfully completed the repair. I will say that I had challenges at almost every step. Getting the inner basket off the centerpost was difficult, as was rocking the outer tub upward from the base.
If a man is somewhat handy, this is a doable ... Read more repair. Be patient and take your time. The video is very helpful and I don't think I could've done the repair without it. It's a pleasure to watch an expert like Steve.
It's gratifying to successfully repair a major appliance such as a washing machine and I look forward to many more years of reliable service from this well-built appliance.
Read less
Was this helpful?
Thank you for voting!
Making a racket.
3 of 3 people
found this instruction helpful.
-
Carl from MARION, KY
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Was this helpful?
Thank you for voting!
a portion of the felt seal was torn loose on the inside of the dryer and needed replacement
3 of 3 people
found this instruction helpful.
-
Keith from EAGAN, MN
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
I spent the most time researching and confirming exactly what part I needed before ordering the shipment. The illustrations and videos available on how to replace the part(s) were VERY helpful and much appreciated.
I followed the instructions seen on video and removed the top and front of dryer. Then pre-fit the new seal - a ... Read more nd stretched it out some while dry to make sure it fit the drum. Once fitted, then I glued 1/2 of it and let it stand for at least 30 minutes and then did the 2nd 1/2 after that. I sure needed clips to hold it in place before moving on to complete both halves. Then I tested it and it tested ok.
I have only noticed 1 spot where some adhesive ran out that shows but it was minor. Had to figure out how the main drive belt work with the pressure pully because it had come loose from the drum. Once past that - it just needed reassembly.
I followed the instructions seen on video and removed the top and front of dryer. Then pre-fit the new seal - a ... Read more nd stretched it out some while dry to make sure it fit the drum. Once fitted, then I glued 1/2 of it and let it stand for at least 30 minutes and then did the 2nd 1/2 after that. I sure needed clips to hold it in place before moving on to complete both halves. Then I tested it and it tested ok.
I have only noticed 1 spot where some adhesive ran out that shows but it was minor. Had to figure out how the main drive belt work with the pressure pully because it had come loose from the drum. Once past that - it just needed reassembly.
Read less
Was this helpful?
Thank you for voting!
dryer blowing cold air
3 of 3 people
found this instruction helpful.
-
Arpad from LOVELAND, CO
- Easy
- More than 2 hours
-
Screw drivers, Socket set
replaced heating element
Was this helpful?
Thank you for voting!
Hard to reach the screws inside the dryer They were on the door side of the dryer and hard to reach, especially if you are a abig guy.
3 of 3 people
found this instruction helpful.
-
Lucy from CHADDS FORD, PA
- A Bit Difficult
- More than 2 hours
-
Screw drivers
Removed the dryer door, unscrewed lint vent.
Was this helpful?
Thank you for voting!
A hole in filter
3 of 3 people
found this instruction helpful.
-
Russ from Vernal, UT
- Really Easy
- Less than 15 mins
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this helpful?
Thank you for voting!
dryer would not turn on
3 of 3 people
found this instruction helpful.
-
donald from MANVILLE, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver
turned off the power and removed the back cover, checked the thermal fuse had no continuity. ordered new part. very easy Installed the new thermal fuse,.replaced the cover, turned on the power and worked fine.
Was this helpful?
Thank you for voting!
Door Latch Broken
3 of 3 people
found this instruction helpful.
-
James from Oceanside, CA
- Very Easy
- Less than 15 mins
Ordered new latch. Installed new latch into the dryer within one minute.
Was this helpful?
Thank you for voting!
Dryer would shut off mid way through cycle and give an E1 error code
5 of 9 people
found this instruction helpful.
-
Dwayne from Bainbridge, PA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back
... Read more
together in reverse. I also took the time to clean any dust and lint out.
Read less
Was this helpful?
Thank you for voting!
not drying completely on the automatic settings
3 of 3 people
found this instruction helpful.
-
Jason from Colorado Springs, CO
- Easy
- Less than 15 mins
-
Pliers
Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen.
... Read more
Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.
Read less
Was this helpful?
Thank you for voting!
Washer wouldn’t drain and spin
3 of 3 people
found this instruction helpful.
-
Thomas from KENT, CT
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re ... Read more moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I re ... Read more moved actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.
Read less
Was this helpful?
Thank you for voting!
Dryer won't start.Only make a click noise.
3 of 4 people
found this instruction helpful.
-
Candido from GREENVILLE, TX
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Remove top,front and panels.change thermal fuse and outlet thermistor.
Was this helpful?
Thank you for voting!
Bulb worked for a couple days and has now burned out, filaments dangling
3 of 4 people
found this instruction helpful.
-
Amy from JUNCTION, TX
- Easy
- Less than 15 mins
-
Screw drivers
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.
I removed the cover and pulled ... Read more out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
I removed the cover and pulled ... Read more out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
Read less
Was this helpful?
Thank you for voting!
Dryer stopped heating
3 of 4 people
found this instruction helpful.
-
Linda from DANVILLE, CA
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
We have a very early model of the He3. We had to follow directions for the He2 model to replace the heater element and thermostat. Access is easy through the front panel, but removing and replacing the element required some force and maneuvering in a small area.
We replaced both the element and the thermostat since we had the ... Read more entire part disconnected and removed. So far working great!
We replaced both the element and the thermostat since we had the ... Read more entire part disconnected and removed. So far working great!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
It came off the dryer support roller
3 of 4 people
found this instruction helpful.
-
Michael from GRANADA HILLS, CA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I actually bought $254 worth of parts almost to point of rebuilding , which included both roller axles, drum belt, idler pulley, both rollers, the cloth that wraps around the drum for edging, and light bulb. 15 years before this the heater element and thermostat and the belt. This dryer is 27 years old and still being used on a daily basi
... Read more
s. The mechanical parts and no LED components can last a life time. The wife always wants new, but this dryer with alittle love and patience is a workhorse. I'm thankful for websites like this. The videos are helpful! Thank you Parts Select! Sincerely, MIke Orkin
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!