1106705 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Quick Boil burner would not stay heated and did not reach the required temperature.
2 of 2 people
found this instruction helpful.
-
Ronald from NOVI, MI
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
The repair was easy. Shut off all power to the range, or unplug it. Remove the sheet metal back from the control panel using a nut driver or socket set. Pull the knob from the front of the control panel. Remove the two Phillips head screws that were hidden behind the knob. Pull the control switch out the back side of the control pan
... Read more
el. Compare the old switch with the new one, to make absolutely sure you have the correct switch. Remove one wire at a time from the old switch and immediately install it in the exact same position on the new switch. When you have successfully transferred all of the wires from the old switch to the new switch, reinstall the new switch using the two Phillips screws. Reinstall the knob and the sheet metal cover. Plug the range back in, and/or turn the power back on. Trying boiling a pan of water to confirm that the repair resolved the issue.
Read less
Was this helpful?
Thank you for voting!
machine wouldn't turn on when lid closed
2 of 3 people
found this instruction helpful.
-
Ellen from NYACK, NY
- Easy
- Less than 15 mins
-
Screw drivers
replaced missing screw and pad and now machine works perfectly
Other Parts Used:
Was this helpful?
Thank you for voting!
The lint filter needed replacement due to what is probably normal wear and tear.
2 of 3 people
found this instruction helpful.
-
Donna from CARY, NC
- Very Easy
- Less than 15 mins
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this helpful?
Thank you for voting!
Dryer electrically dead
3 of 6 people
found this instruction helpful.
-
Dale from Anderson, IN
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged power cord. Removed rear panel screws and panel . Removed the two wires connected to part. Removed two screws holding part and replaced all components in reverse order.
Was this helpful?
Thank you for voting!
It was the heat safety switch in the old drive motor
2 of 3 people
found this instruction helpful.
-
Andrew from HATTIESBURG, MS
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward
Was this helpful?
Thank you for voting!
Dryer kept throwing the E1 error indicating the thermistor needed replacement
2 of 3 people
found this instruction helpful.
-
Rory from LEESBURG, VA
- Easy
- 15 - 30 mins
-
Socket set
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back i
... Read more
n, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Screen ripped
2 of 3 people
found this instruction helpful.
-
Cindy from BENZONIA, MI
- Very Easy
- Less than 15 mins
Dropped new filter in.
Was this helpful?
Thank you for voting!
the fastener became loose and dropped into the stove
2 of 3 people
found this instruction helpful.
-
George E from OCALA, FL
- Really Easy
- 30 - 60 mins
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this helpful?
Thank you for voting!
The fan wheel had a blade break off, my bad.
2 of 3 people
found this instruction helpful.
-
Terry from ETTERS, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Was this helpful?
Thank you for voting!
Heater element died
1 person
found this instruction helpful.
-
Jerry from AUBURN, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver
Pretty easy repair and I am not very handy. I believe they engineer these machines so you hire someone to do the job. They could place that part in an area where it is easier to get to, like a door on the side or something
Was this helpful?
Thank you for voting!
Lint screen tore and had a side that was loose so it didn't catch all the lint and cut your fingers
1 person
found this instruction helpful.
-
Wayne from ALBANY, OR
- Really Easy
- 30 - 60 mins
Removed the old screen and simply put in the new one
Was this helpful?
Thank you for voting!
Plastic part in door catch was broken so door would not lock to allow the dryer to operate
1 person
found this instruction helpful.
-
Henri from SILER CITY, NC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the part with pliers but could not remove it so I removed the screws that hold the front part of the door. I took the front part off, removed the broken plastic and then lifted on side of the catch so that the bottom of the front part came thru the door and then was able to remove the door latch. The installation of the
... Read more
new part took about 15 seconds to put in by pushing it into the opening where the broken part was removed. I put the front part of the door back and put the screws back and the dryer works fine.
Read less
Was this helpful?
Thank you for voting!
No heat
1 person
found this instruction helpful.
-
DENNIS from SAINT LOUIS, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
You tube
Was this helpful?
Thank you for voting!
F-26 Fault message
1 person
found this instruction helpful.
-
DW from ALVIN, TX
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger
Thank You.
DW Pranger
Was this helpful?
Thank you for voting!
Dryer would not start due to over heating
1 person
found this instruction helpful.
-
John from HOPATCONG, NJ
- Easy
- 30 - 60 mins
-
Socket set
Followed the video.
Was this helpful?
Thank you for voting!