1106705 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken door catch
1 person
found this instruction helpful.
-
ERNST from FLOSSMOOR, IL
- Really Easy
- 30 - 60 mins
pushed the broken catch into the door and snapped the new one back in. Works perfectly!
Was this helpful?
Thank you for voting!
Clothes would not dry
1 person
found this instruction helpful.
-
John from WOODBRIDGE, VA
- Easy
- 1- 2 hours
-
Nutdriver
Unplug from electric ? outlet. Set the meter to ohm setting, check part ,no reading. Remove old part ,check new part with meter ,get a reading of 11 or more mA. Install new part and blower cover done.
Was this helpful?
Thank you for voting!
Dryer would power up but not run.
1 person
found this instruction helpful.
-
Jeremy from VILLA RICA, GA
- Easy
- 30 - 60 mins
-
Nutdriver
Removed front of dryer. Located thermal fuse, replaced blown thermal fuse. Reassembled.
Was this helpful?
Thank you for voting!
No heat!!
1 person
found this instruction helpful.
-
David from ORANGE, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Remove top, remove two front panels, remove rear panel to access drive motor release tensioner. Remove drum to access to heating element enclosure. Replace and reinstall after vacuuming all accumulated lent.
Was this helpful?
Thank you for voting!
Dryer stopped heating
1 person
found this instruction helpful.
-
Anna from Marietta, GA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Determined via multimeter that either the thermostat or thermal fuse were not working, so ordered the kit (best value, contains both parts).Easiest access is from the rear, so removed rear panel and top of dryer (required) and also the vent tube since it was in the way. Unhooked wires from both parts, used socket to remove nuts holding ea
... Read more
ch one on, put new ones in place, re-attached wires. Replaced vent tube, vacuumed entire inside of dryer (good idea). Put back/top back on and the dryer worked/heated perfectly immediately.
Read less
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person
found this instruction helpful.
-
Joe from St. Louis, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
The dryer would shut off mid-cycle.
1 person
found this instruction helpful.
-
Michael from ONEONTA, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench set
I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dry
... Read more
er works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.
Read less
Was this helpful?
Thank you for voting!
Start button failed to keep dryer running; no heat
1 person
found this instruction helpful.
-
William from APPLE VALLEY, CA
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers
Dryer is still in pieces after two weeks, dependent upon my time and ability to work on the project. I usually dry my clothes on an outside line, anyway. I especially appreciate Steve's videos demonstrating step-by-step procedures for disassembly, part installation, and reassembly. Very thorough. I timed each presentation---five minut
... Read more
es for one, less than ten for the other. I watched the videos several times and took notes, so I would have the procedures in front of me while working on the unit at the other end of the house, I'm 77, forgetful. When I disassembled my unit, I noticed several rusted areas, so decided not to complete the project until I could get to the store for paint. As a primary care-giver for a severely dementiated 79-year Old Lady, I have to arrange for a relief to go shopping. That's why the machine is still in pieces. Got the paint, though, so back to work---eventually. When I disassembled the dryer, tucked away in the bottom was a very informative TECH SHEET, the discovery of which ticked me off that it wasn't provided with the owner's manual. At the bottom it says, "For Service Technicians' Use Only." In my house, I'm the "...Service Technician...," chief cook and bottle washer, launderer and litter box attendant.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Door would not clisr
1 person
found this instruction helpful.
-
LANA from INDIANAPOLIS, IN
- Very Difficult
- More than 2 hours
-
Pliers, Screw drivers
Had to force the old door catch out using the putty knife didn't work. Worked on it until I finally forced it out.
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people
found this instruction helpful.
-
Enrique from Miami Shores, FL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w
... Read more
asher door bang shut.Took longer than expected, but each procedure was simple.
Read less
Was this helpful?
Thank you for voting!
door catch broken and fell into door
1 person
found this instruction helpful.
-
Phillip from FORSYTH, MO
- Very Easy
- Less than 15 mins
snapped new catch into door
Was this helpful?
Thank you for voting!
Torn filter seal
1 person
found this instruction helpful.
-
James from SCOTTSDALE, AZ
- Very Difficult
- Less than 15 mins
Remove old filter, throw it away, replace with new filter.
Was this helpful?
Thank you for voting!
Door catch on dryer stopped catching (meaning the door would not stay closed)
1 person
found this instruction helpful.
-
John from AUBURNDALE, MA
- Very Easy
- Less than 15 mins
I placed the putty knife on the top part of the door catch and when that came loose I placed the putty knife on the bottom of the door catch and pushed on the putty knife and the door catch came out of its place. I then just popped the new door catch in place. Total repair time 45 seconds. The door now closes.
Was this helpful?
Thank you for voting!
Door catch broken
1 person
found this instruction helpful.
-
Polly from POTTSVILLE, AR
- Very Easy
- Less than 15 mins
Didn't have a putty knife, so used a flathead screwdriver to carefully pop out the top, then bottom of the catch. New one easily popped in. Took less than one minute!
Was this helpful?
Thank you for voting!
Latch Replacement
1 person
found this instruction helpful.
-
Kathy from W TERRE HAUTE, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Used a screwdriver to pry out the bottom of the latch then the top. Pulled old latch out, then snapped new one in. Super Simple fix.
Was this helpful?
Thank you for voting!