1106705 Kenmore - Instructions

All Instructions for the 1106705
31 - 45 of 249

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Dryer not heating
16 of 27 people found this instruction helpful.
  • Stephen from Andalusia, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.
Was this helpful?
Thank you for voting!
Heater Element bad.
10 of 11 people found this instruction helpful.
  • Christian from JOHNSTON, IA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Followed video step by step. Perfect instructions. I’d only add that you should get and wear mechanics gloves. My hands got torn up by the sharp metal edges taking apart and putting it back together. Ouch!!
So happy with Partselect though. Super fast shipping and a perfect instructional video. Thanks!!

P.S. Wear gloves! !!
Was this helpful?
Thank you for voting!
broken clip on top panel hold down
15 of 26 people found this instruction helpful.
  • Mark from Huntington Station, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
Replacement of the water inlet vaqlve
11 of 14 people found this instruction helpful.
  • William from Chester, NJ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
First I disconnected the inlet hoses. After lifting up the cover the electrical wires were marked and disconnected from the old valve. Next the short hose from the old valve to the tub was removed. Then the old valve was removed from the washing machine by removal of two mounting screws. The new valve was installed in the reverse orde r. New hose clamps were installed on the short hose from the valve to the tub. New washers were installed on the hoses which connected to the valve. A test was made to check for any leaks.
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
latch on door broke
11 of 16 people found this instruction helpful.
  • donna from westmoreland, TN
  • Easy
  • Less than 15 mins
  • Pliers
very easily
Was this helpful?
Thank you for voting!
The seal came off our dryer door.
10 of 15 people found this instruction helpful.
  • Janet from LOS ANGELES, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Take door off dryer (unscrew four screws). Lay door on flat surface. Using glue provided glue down new seal. Put dryer door back on and you're done!
Was this helpful?
Thank you for voting!
Dryer would not turn on
8 of 10 people found this instruction helpful.
  • Pam from Chandler, AZ
  • Really Easy
  • Less than 15 mins
  • Socket set
We took the screws off of the back, took out the thermal fuse and replaced it with the new one.
We watched a video of how to do it which made it so easy.
Works great!
Was this helpful?
Thank you for voting!
No heat
7 of 7 people found this instruction helpful.
  • Rick from LANESVILLE, IN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I don't have instructions ,I watched the link provided by parts select. I just wanted to say I have never been a wiz at home repairs.it took so long because I am 62 with autheritis in my hands and the dryer had to be taken down to a motor and a base but I took the time to clean every inch of the dryer scary to see so much dryer lint insid e the dryer.i am just going to say if I can do it anybody could fix their own dryer ,just take your time ,let your hands take a break. And keep the repair instructions close by
Was this helpful?
Thank you for voting!
Loss of cold water
8 of 10 people found this instruction helpful.
  • David from Powell, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Removed the top latches with a nut driver. Removed the washing machine top. Used a nut driver to remove the valve. Used pliers to remove and replace the outlet hose clamp. Used pliers to remove and replace inlet hoses.

I have kept this washer and dryer running for 27 years now by replacing parts. I was going to replace them thi s time but for a $20 part they still run ok. I bet I can use the old valve for a garden irrigation project too !
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people found this instruction helpful.
  • Joseph from Austin, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Was this helpful?
Thank you for voting!
Dryer would run 1 min then stop running with some heat in drum
10 of 18 people found this instruction helpful.
  • Bob from CHULA VISTA, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Videos are excellent to open and access internal parts. It turned out a rat was killed in the blower fan when we first encountered the problem. This prevented the blower from turning which interfered with motor function.

This required removing drum & belt, disconnecting motor clips, blower belt, and blower housing. The blower housing needed to be disassembled. Having a 5/16” & 1/8” ratcheting nut driver makes this process much easier. Don’t try this with a wrench.

After getting rid of the rat and decomposition, we sanitized the entire housing with soap & chlorine bleach.

Reassembly was uneventful and relatively easy. We ended up replacing 4 rollers, 2 belts (drum belt & blower belt), the thermistor which was damaged as a result of the blocked blower.
Was this helpful?
Thank you for voting!
Lens melted because paper got behind the lens and was heated by the lamp.
6 of 6 people found this instruction helpful.
  • Chris from Valley Stream, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1 screw to replace.
Was this helpful?
Thank you for voting!
Broken door latch
6 of 6 people found this instruction helpful.
  • William from ROCK ISLAND, IL
  • Very Easy
  • Less than 15 mins
  • Pliers
Followed video instructions using flat scraper & pliers (easy).Tried to remove "SPARE" latch on other side of door. Even removed door myself (Easy).Tried for (45) minutes without success. Ordered part @ 11:30 pm. Replaced door easily by myself by leaving bottom screw for each hinge in place & replaced broken latch. Received new latch in (5) days. Removed broken latch without tools & replaced new latch in (15) seconds. Need help from any "Ladies" who can remove second latch so it is available for next replacement. This "Engineer" was too lazy to remove the screws around the door because he was going to "Follow the Video". Overall it was an "Easy Fix". Keep the 'Videos"coming.
Was this helpful?
Thank you for voting!
All Instructions for the 1106705
31 - 45 of 249