1106509 Kenmore Washer Dryer Combo - Instructions

All Instructions for the 1106509
76 - 90 of 167

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Door Wouldn't Shut
1 of 2 people found this instruction helpful.
  • Megan from Kettering, OH
  • Really Easy
  • Less than 15 mins
My husband is the one who fixed the door. He said he just popped it into place and was done in just a couple of seconds! The best part though was the quick service we received. . . I ordered the part around 10:30 in the morning, and it was at my front door by 5pm the next day!!! What great service!!!! We will definitely do business a gain with partselect. Com if we ever need more parts.
Was this helpful?
Thank you for voting!
Door wouldn't fasten shut
1 of 2 people found this instruction helpful.
  • Susan from Laingsburg, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Popped the latch out and popped a new one in.

The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se rvice. You made my life easier.
Was this helpful?
Thank you for voting!
The dryer door catch wouldn't hold the door closed
1 of 2 people found this instruction helpful.
  • Gerald from Thompsonville, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!
Was this helpful?
Thank you for voting!
dryer latch engagem ent
1 of 2 people found this instruction helpful.
  • Earl from Terre Haute, IN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
our son was able to diagnosis and order the part and very pleased with quite response. Dryer now working fine.
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people found this instruction helpful.
  • Rick from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people found this instruction helpful.
  • Daniel from TRENTON, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Was this helpful?
Thank you for voting!
Door keeps opening while operating
1 of 2 people found this instruction helpful.
  • Carmine from MASSAPEQUA PK, NY
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people found this instruction helpful.
  • Edward from Nanuet, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people found this instruction helpful.
  • Andris from Sands Point, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Was this helpful?
Thank you for voting!
Washing machine over 20 years old but still runs strong door switch actuator spring broke original spring was not availible.
0 of 1 people found this instruction helpful.
  • Larry from Elmhurst, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.
Was this helpful?
Thank you for voting!
The dryer door kept popping open while in use.
0 of 1 people found this instruction helpful.
  • Joseph from Margate, FL
  • Easy
  • 15 - 30 mins
I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to ma ke this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...
Was this helpful?
Thank you for voting!
Lever was broke off
0 of 1 people found this instruction helpful.
  • linda from las cruces, NM
  • Easy
  • 15 - 30 mins
  • Screw drivers
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this helpful?
Thank you for voting!
Dryer door would not close
0 of 1 people found this instruction helpful.
  • Felipe from Helotes, TX
  • Really Easy
  • Less than 15 mins
Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!
Was this helpful?
Thank you for voting!
door wouldn"t close tightly
0 of 1 people found this instruction helpful.
  • Noreen from Fairfax, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
removed the broken part and replaced with the new one
Was this helpful?
Thank you for voting!
the dryer would not turn on
0 of 1 people found this instruction helpful.
  • James from Shortsville, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in ab out 10 minutes.
Was this helpful?
Thank you for voting!
All Instructions for the 1106509
76 - 90 of 167