1106509 Kenmore Washer Dryer Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Light stayed on, inside dryer. Dryer no workie
1 person
found this instruction helpful.
-
Steven from New Richmond, WI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You
... Read more
just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Read less
Was this helpful?
Thank you for voting!
Broken door switch
2 of 4 people
found this instruction helpful.
-
john from el paso, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and
... Read more
pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.
Read less
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person
found this instruction helpful.
-
Victor from NORFOLK, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person
found this instruction helpful.
-
Tammy from glenford, OH
- Very Easy
- Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Susan from HUDSON, MA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person
found this instruction helpful.
-
Mark from TERREBONNE, OR
- Very Easy
- Less than 15 mins
-
Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo
... Read more
w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Read less
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Frank from ENDICOTT, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 people
found this instruction helpful.
-
Jimmy from MEMPHIS, TN
- Very Easy
- Less than 15 mins
-
Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this helpful?
Thank you for voting!
Door keeps opening while operating
1 of 2 people
found this instruction helpful.
-
Carmine from MASSAPEQUA PK, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed old catch and strike with screwdriver and needle nose pliers. Installed new parts. My old catch did not have comparible numbers so I just used the yellow one. Worked fine.
Was this helpful?
Thank you for voting!
dryer latch engagem ent
1 of 2 people
found this instruction helpful.
-
Earl from Terre Haute, IN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
our son was able to diagnosis and order the part and very pleased with quite response. Dryer now working fine.
Was this helpful?
Thank you for voting!
Dryer door kept opening
1 of 2 people
found this instruction helpful.
-
Jennifer from Big Timber, MT
- Easy
- Less than 15 mins
-
Screw drivers
Popped out the old door catch kit and replaced it with the new one! Easy!!
Was this helpful?
Thank you for voting!
Door wouldn't fasten shut
1 of 2 people
found this instruction helpful.
-
Susan from Laingsburg, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Popped the latch out and popped a new one in.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se ... Read more rvice. You made my life easier.
The real story here is that there was an ANSWER and a SOLUTION, to what was a GREAT
annoyance. If I wouldn't have found a part, I may have run off and bought a new dryer, when I really didn't need to, or paid A LOT of money for a repair man to come out. THANK YOU for your se ... Read more rvice. You made my life easier.
Read less
Was this helpful?
Thank you for voting!
The dryer door catch wouldn't hold the door closed
1 of 2 people
found this instruction helpful.
-
Gerald from Thompsonville, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered the door catch kit on a Wednesday at it arrived Saturday AM. It took less than 1 minute to pry out the old catch with a flat screwdriver and pop in the new one!
Was this helpful?
Thank you for voting!
Door latch snapped off.
1 of 2 people
found this instruction helpful.
-
Karen from Randle, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
We got the part so fast we were both surprised. My husband installed the part by just seeing how the old one came off. It was simple and fairly quick. Except that his hands are so big they had a hard time fitting in to where the part needed to go. Just opened the top of the dryer, took the old part out and put the new one in.
Was this helpful?
Thank you for voting!
Broken door actuator spring -interposer for motor control
1 of 2 people
found this instruction helpful.
-
Stephen from Vancouver, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed previous comments and took 5 minutes to replace. Be careful to hold spring and switch together because easy to separate and drop. Two screws to remove for switch, two to remove for lint trap, pop the lid up and switch / spring is easy to access.
Was this helpful?
Thank you for voting!