1106509 Kenmore Washer Dryer Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer door actuator lever broke
3 of 4 people
found this instruction helpful.
-
Mark from Clarksburg, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I disconnected the dryer from the electric. I removed the lid to the dryer by first removing the lint door screws and prying the lid off properly. Disconnected the wires to the door switch. Removed the screws from inside the door and carefully removed teh actuator. Seperated the actuator from the switch and replaced the broken actuator. R
... Read more
einstalled the actuator and switch and screwed the assembly back in place. Reconnected the wires, lowered the dryer lid and screwed the lint door screws back in place. It Worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 4 people
found this instruction helpful.
-
Wayne from Rosenberg, TX
- Easy
- 15 - 30 mins
-
Screw drivers
Did not hear the "clicking noise of the door switch when the dryer door was shut. First I unplugged the dryer from the socket. Next I removed the two screws that hold the lint filter receptacle. Next I pried the top of the dryer open with a screwdriver. Next I removed the two screws that held the switch actuator spring in place locate
... Read more
d just inside the top of the door. Then I removed the old spring from the door switch and replaced with the new. Not too difficult once the problem was diagnosed.
Read less
Was this helpful?
Thank you for voting!
Door latch catch broke
4 of 7 people
found this instruction helpful.
-
Raymond from Washington, DC
- Really Easy
- Less than 15 mins
-
Pliers
I squeezed the latch catch with a pair of pliers and pushed it in the catch hole. But that was the final repair. There were two "repairs" before that. First, we used two commercial grade rolls of wide plastic tape to tape the dryer door shut each time we used it, for a year, until we ran out of tape. Second, we positioned a chest of dra
... Read more
wers in front of the dryer and wedged a 1" x 4" against the door. Very effective. Then I broke down and ordered the $3 catch.
Read less
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people
found this instruction helpful.
-
WILFRED from NORTH HIGHLANDS, CA
- Really Easy
- Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
Door switch would not let dryer operate
2 of 2 people
found this instruction helpful.
-
George from Rio Communities, NM
- Very Easy
- Less than 15 mins
-
Screw drivers
Move dryer away from wall. Unplug the dryer. Open the hinge top from the front edges of dryer. Remove the two screws holding the filter channel onto the top of dryer. Lean the top of dryer back away from the front . Open the dryer door, Locate switch from the top looking into the dryer top opening where you have just leaning the top bac
... Read more
k out of your way. Unplug the wire from the old switch. remove the old switch and bracket using the flat blade screwdriver for screw removal.
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Place the wire on the new switch using the normally open contacts. place switch on bracket and gently position the bracket and switch over the holes designed for the switch and tighten screws using the new Phillips head screws sent with the new switch. place the top back into place and replace the filter channel screws plug in the dryer and job finished. easy as 1-2-3
Read less
Was this helpful?
Thank you for voting!
Dryer door latch broke and door wouldn’t stay shut.
2 of 2 people
found this instruction helpful.
-
Susan from WARREN, NJ
- Very Easy
- Less than 15 mins
-
Screw drivers
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people
found this instruction helpful.
-
James from Richmond, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people
found this instruction helpful.
-
Laszlo from Vienna, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people
found this instruction helpful.
-
katherine from Salem, OR
- Easy
- 15 - 30 mins
-
Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw
... Read more
s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people
found this instruction helpful.
-
Victoria from Roslyn Heights, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag
... Read more
ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Read less
Was this helpful?
Thank you for voting!
Dryer wouldn't restart when start button pressed
2 of 3 people
found this instruction helpful.
-
Charles from Cape Girardeau, MO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed c
... Read more
lip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Read less
Was this helpful?
Thank you for voting!
the fastener became loose and dropped into the stove
2 of 3 people
found this instruction helpful.
-
George E from OCALA, FL
- Really Easy
- 30 - 60 mins
This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark
George Clark
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people
found this instruction helpful.
-
satyavenkata from Bentonville, AR
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
door would stay closed
1 person
found this instruction helpful.
-
william from KILLEEN, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!