1106509 Kenmore Washer Dryer Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person
found this instruction helpful.
-
Steven from New Richmond, WI
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You
... Read more
just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Read less
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person
found this instruction helpful.
-
Melody from TEXARKANA, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
dryer door wouldn't catch, catch was broken
1 person
found this instruction helpful.
-
Theodore from Tyler, TX
- Really Easy
- Less than 15 mins
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this helpful?
Thank you for voting!
broken door catch
2 of 4 people
found this instruction helpful.
-
Michael from Goddard, KS
- Really Easy
- Less than 15 mins
the part fit perfectly, it just snaped right into place.
Was this helpful?
Thank you for voting!
The door whould not close enough for the dryer to work.
1 person
found this instruction helpful.
-
Frank from Union Beach, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.
Was this helpful?
Thank you for voting!
dryer wouldn't turn on
1 person
found this instruction helpful.
-
Kim from Northridge, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions
... Read more
on your website!! Simple as could be!
Read less
Was this helpful?
Thank you for voting!
catch was missing to close dryer door
2 of 4 people
found this instruction helpful.
-
DONNA from SAN LORENZO, CA
- Really Easy
- Less than 15 mins
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this helpful?
Thank you for voting!
door latch broke
1 person
found this instruction helpful.
-
Debra from Oakland, NJ
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out the old latch and replaced with a new one
Was this helpful?
Thank you for voting!
door catch broke therefore dryer door would not close
1 person
found this instruction helpful.
-
vernette from sprague, WA
- Really Easy
- Less than 15 mins
just put the new part in the door---sooo easy! THANK YOU!
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person
found this instruction helpful.
-
Victor from NORFOLK, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person
found this instruction helpful.
-
Barbara from NORTH EASTON, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person
found this instruction helpful.
-
Kenneth from UPPR MARLBORO, MD
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Susan from HUDSON, MA
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person
found this instruction helpful.
-
Mark from TERREBONNE, OR
- Very Easy
- Less than 15 mins
-
Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo
... Read more
w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Read less
Was this helpful?
Thank you for voting!