1106509 Kenmore Washer Dryer Combo - Instructions

All Instructions for the 1106509
106 - 120 of 167

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
latch not working on Kenmore dryer
0 of 1 people found this instruction helpful.
  • sally from Houston, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Was this helpful?
Thank you for voting!
Dryer door wouldn't stay latched shut during cycle
0 of 1 people found this instruction helpful.
  • KRISTIN from DENVER, CO
  • Really Easy
  • Less than 15 mins
  • Pliers
In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!
Was this helpful?
Thank you for voting!
The switch in the door of the dryer was broken so it would keep running when you opened the door
0 of 1 people found this instruction helpful.
  • Matt from Stilwell, KS
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.
Was this helpful?
Thank you for voting!
Dryer stopped working
0 of 1 people found this instruction helpful.
  • Mike from Conway, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen th e two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.

Advice: Don't slam the dryer door. The actuator will last longer.
Was this helpful?
Thank you for voting!
Dryer would not come on
0 of 1 people found this instruction helpful.
  • Steven from Bassett, VA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replaced the cap over the door switch so when the door closed the switch was engaged
Was this helpful?
Thank you for voting!
Dryer would not start
0 of 2 people found this instruction helpful.
  • Edwin from Shelby, NC
  • Easy
  • Less than 15 mins
  • Screw drivers
Took top of d then dryer loose then replaced switch actuator put dryer top back in place. Not that hard.
Was this helpful?
Thank you for voting!
The dryer would not run.
0 of 2 people found this instruction helpful.
  • Kevin from North Aurora, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you
Was this helpful?
Thank you for voting!
Broken dryer door latch.
0 of 2 people found this instruction helpful.
  • Fred from Encino, CA
  • Really Easy
  • Less than 15 mins
Fantastic site and service !!! Using your site, I i'd my needed part in about 10 minutes. I received my Whirlpool dryer door latch part from you in less than 12 hours. Per your internet site instructions, I replaced the part in a few seconds (just popped it into the slot) and my wife had a working dryer for her Sunday wash. I would hav e been out $55 and 4 to 7 days waiting for a service call if I had used my home warranty service contractor. Using your service, the part(s) and shipping were just over $12.
Was this helpful?
Thank you for voting!
dryer door wouldnt latch shut
0 of 2 people found this instruction helpful.
  • Phyllis from Riva, MD
  • Really Easy
  • Less than 15 mins
  • Wrench set
ordered new latch kit and repaired, very easy thank you
Was this helpful?
Thank you for voting!
Old Part Broke Off
0 of 2 people found this instruction helpful.
  • Steve from Edina, MN
  • Really Easy
  • Less than 15 mins
Took 5 seconds, just snapped in the slot, didn't need any tools.
Was this helpful?
Thank you for voting!
door latch/ catch completely shattered
0 of 3 people found this instruction helpful.
  • Edward from Lowell, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken of f and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.
Was this helpful?
Thank you for voting!
Door latch broken
  • Janet from Manlius, NY
  • Really Easy
  • Less than 15 mins
For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.
Was this helpful?
Thank you for voting!
Dryer won't start
  • Michael from Cincinnati, OH
  • Easy
  • 15 - 30 mins
  • Screw drivers
Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.
Was this helpful?
Thank you for voting!
Dryer door switch broken or burned out
  • James from Iota, LA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.
Was this helpful?
Thank you for voting!
dryer would not run
  • Jeffery from Cordova, AL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing b ack together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.
Was this helpful?
Thank you for voting!
All Instructions for the 1106509
106 - 120 of 167