11046 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The video supplied by you was great and it worked very well.
3 of 3 people
found this instruction helpful.
-
Michael from NEWBERG, OR
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
It was fast and pretty easy to do.
Was this helpful?
Thank you for voting!
Replace Bellows between door and tub
5 of 9 people
found this instruction helpful.
-
Gerald from Douglas, AL
- Easy
- 30 - 60 mins
-
Screw drivers
Remove top and front
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 ... Read more people
connect bellows to door with spring clip
Care taken to unplug door wiring
should have taken notes or photos where srews go and order
remove old bellows large hose clamp and sping tensioned clip
clean surfaces
install new bellows on tub only
put all panels and door together
Connecting wiring to door and strain relief takes 2 ... Read more people
connect bellows to door with spring clip
Read less
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 people
found this instruction helpful.
-
Helen from NASHUA, NH
- Really Easy
- 30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
Hinge broke
3 of 3 people
found this instruction helpful.
-
Lindsey from STEWART MANOR, NY
- Very Easy
- 30 - 60 mins
We read your you tube instruction and followed the video
Was this helpful?
Thank you for voting!
Drain/Pump bellow (washer tub to pump hose) punctured. Leaked excessive amount of water.
3 of 3 people
found this instruction helpful.
-
Vern from LAREDO, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Removed top lid (only to be able to remove pressure sensor hose easily). Removed hose clamps and tied the ends together in order to keep in loose position. Then squeezed the damaged hose up between sidewall and tub to remove pressure sensor rubber pipe. Installed Hose with clamps tied in the loose position with thin wire. Attached the
... Read more
pressure sensor pipe. Loosened the thin wire holding clamps loose. Tested for leaks by running washer. Leak repaired.
Read less
Was this helpful?
Thank you for voting!
Broken hinge
3 of 3 people
found this instruction helpful.
-
Anthony from JACKSONVILLE, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed door from washer, remove hinge from door. Then slip in hinge and tighten hinge to door. Then attach door. It works and the most important thing the wife is happy
Was this helpful?
Thank you for voting!
I was getting a sewer smell when the washer drained I did every cleaning technique and didn't solve the problem then I cleaned the inside drain hose and that helped so I replaced the hose and problem solved.
3 of 3 people
found this instruction helpful.
-
anthony from EASTPOINTE, MI
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.
I replaced the hose and reinstalled the panels and I was do ... Read more ne.
I replaced the hose and reinstalled the panels and I was do ... Read more ne.
Read less
Was this helpful?
Thank you for voting!
The part was made wrong and did not fit.
3 of 3 people
found this instruction helpful.
-
Doug from ROCHESTER HLS, MI
- Very Easy
- Less than 15 mins
The plastic tabs were too large to fit into the washer's slotted hole in the washer cage. I initially bought this part from a PartSelect competitor and it was made wrong as well. Whirlpool themselves showed this part on back order so the faulty part originated in a Whirlpool order to a vendor. The reason for this reply is that PartSelect
... Read more
resolved this bad part issue within 2 hours and 1 phone call. The competitor has not resolved anything yet in 3 weeks and 5 emails with image proof.
Read less
Was this helpful?
Thank you for voting!
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
3 of 3 people
found this instruction helpful.
-
scott from DENVER, NC
- Really Easy
- Less than 15 mins
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.
Was this helpful?
Thank you for voting!
Pump not working
4 of 6 people
found this instruction helpful.
-
Darrell from Lady Lake, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Replaced pump
Was this helpful?
Thank you for voting!
tub would not turn
3 of 3 people
found this instruction helpful.
-
claude van from big sandy, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
take the back cover off and put belt on. the belt is a tight fit and requires sone effort, but can be done.
Was this helpful?
Thank you for voting!
F 21 code kept appearing even though trap clean out was clear.
4 of 6 people
found this instruction helpful.
-
Michael from LUCKEY, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Replaced drain pump took longer to soak up water than actually replacing the pump motor with mine having the pedestal underneath I did not have to tip the washer at all so it was fast and easy. Three screws taking the front cover off a screwdriver lifting the Rubber and sliding the motor off and pair of pliers 4 to hose clamps making it a
... Read more
breeze.
Read less
Was this helpful?
Thank you for voting!
the pump wasnt puping out the water
3 of 4 people
found this instruction helpful.
-
Evette from Mayfield, NY
- Easy
- 15 - 30 mins
-
Pliers, Socket set
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
Was this helpful?
Thank you for voting!
replace the pump motor
3 of 4 people
found this instruction helpful.
-
Jay from MALVERN, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
First tilt the washer back so you can drain water from the lines to the pump and the pump itself. Disconnect the lines with a pair of pliers and use a screwdriver to move the rubber stopper so that the pump will move to the right. With pump now in position to lift up and out of the washer , do it so you can disconnect the wire assembly. R
... Read more
eplace the pump starting with the wires, then slide it in place and secure it with the rubber stopper. Attach the lines and make sure they are well sitted and clamped. set on feet and you are ready to wash.
Read less
Was this helpful?
Thank you for voting!
Broken Strike on Washer Door - prevented door from latching, and washer would not start
3 of 4 people
found this instruction helpful.
-
David D from Severn, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
The end of the strike had broken off, and the pictures did not clearly show there was a cross-member at the end of the strike. That crossmember is what broke on the old strike. The strike has only two screws, both requiring a Torx bit (#20, I believe). Unscrew both screws to remove the strike plate. It was a little difficult to get out -
... Read more
it has a curved top to lock into the top slot, but the bottom slides slightly down into another slot. There isn't a lot of room in the opening to slide the strike up and down and get it out. Putting the new strike on is easier - ensure the curved end fits into the slot at the top and slide it up just a bit, push the bottom of the strike plate in, then let it drop right into place, and reinsert the screws. The only problem I had was the strike's holes for the screws are slotted horizontally, so the strike can be positioned across almost 3/8". The latch would not engage the strike the first time, so I had to loosen the screws and reposition the strike a bit. This time it latched, but the fit wasn't quite right, so I adjusted it again to get it where I needed it.
Read less
Was this helpful?
Thank you for voting!