11046 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Getting “sud” or “F35” errors intermittently
4 of 4 people
found this instruction helpful.
-
Dan from STOCKBRIDGE, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 3 screws from back of top panel, slid top off, twisted APS sensor 90 degrees, popped out of mount, removed hose and elect. connector, replaced with new APS sensor and reinstalled. Ran diag test, passed with no issues.
Was this helpful?
Thank you for voting!
Door was not closing properly, broken swivel arm under hinge.
4 of 4 people
found this instruction helpful.
-
Gustavo from YOUNGSTOWN, OH
- Very Easy
- 15 - 30 mins
removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.
Was this helpful?
Thank you for voting!
pump would not pump out the water in the tub
4 of 4 people
found this instruction helpful.
-
Ron from LITTLETON, CO
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
just changed out the pump. easy
Was this helpful?
Thank you for voting!
baffle connectors worn off
5 of 7 people
found this instruction helpful.
-
richard from chetek, WI
- Really Easy
- 15 - 30 mins
Placed baffle inside of washer and pulled to lock into place. EASY!!!
Was this helpful?
Thank you for voting!
PUMP HOUSING LEAKS
5 of 8 people
found this instruction helpful.
-
JOHN from OMAHA, NE
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
REMOVE AND REPLACE. FLEXIBLE RUBBER CONNECTOR WAS NOT A EXACT REPLACEMENT, THE ORIGANIL HAD A BACK STOP VALVE, NOT SURE OF THE EFFICATE ON MACHINE.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer would not drain flashing f-21 code
4 of 5 people
found this instruction helpful.
-
Casey from REXBURG, ID
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Took it old pump and replaced with new pump VERY EASY
Was this helpful?
Thank you for voting!
Multiple water leaks, all rubber parts are chewed up from a mouse 1/
4 of 5 people
found this instruction helpful.
-
Tom from SAN MARCOS, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.
Was this helpful?
Thank you for voting!
Spring balanced tub violent shake on spin
4 of 5 people
found this instruction helpful.
-
Paul from TARPON SPGS, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
Washer was on a 13 inch high platform I built for front.load Heat washer and dryer. Removed 3.screws from bottom of front panel and had access to all 4 shocks..front and rear. All shocks were unattachedeither at base or on tub. Easy to install all 3 from front without moving Mach. I figured if 1 or 2 shocks failed the violent.movement bro
... Read more
ke the other 2. Purrs like.a.kitten now. No bearing.or spring.damage.
Read less
Was this helpful?
Thank you for voting!
Water leaked from front bellows. (Door gasket)
4 of 5 people
found this instruction helpful.
-
Joseph from EAST SYRACUSE, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Easier if you block up front feet on 2x4 blocks. remove bottom front panel. Remove detergent dispenser tray. Remove top front panel. On door remove large round retainer clamp to bellows. (Pop off with screwdriver.) Remove door. Remove inner bellows clamp. Use phillips screwdriver to loosen it. If the input water filler hose is in
... Read more
the way, pull it out, but don't forget to put it back on or a flood will ensue!! Replace by doing everything in reverse order.
Read less
Was this helpful?
Thank you for voting!
Ripped bellowspul
4 of 5 people
found this instruction helpful.
-
WILLIAM from REPUBLIC, MO
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.
Was this helpful?
Thank you for voting!
Pump not draining the water out.
4 of 5 people
found this instruction helpful.
-
Martin from Kotzebue, AK
- Easy
- 15 - 30 mins
-
Screw drivers
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one ... Read more in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one ... Read more in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
Read less
Was this helpful?
Thank you for voting!
Bellow was damaged,water leakage.
5 of 8 people
found this instruction helpful.
-
Gopaul from Queens, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
First,we took apart the front of the washer and then we removed the old bellow and put the new one on.After we put back up the front of the washer and open the door to put the clamp on then after we unlocked it.After it was working good as new.
Was this helpful?
Thank you for voting!
The door bellows had a cut in it
4 of 5 people
found this instruction helpful.
-
Arthur from MORGANTOWN, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.
Was this helpful?
Thank you for voting!
No problem as instructed.
4 of 5 people
found this instruction helpful.
-
John from BOYLSTON, MA
- Really Easy
- 30 - 60 mins
As video instructed
Was this helpful?
Thank you for voting!
Fault code F-21 and SD
3 of 3 people
found this instruction helpful.
-
Kevin from WEST BRANCH, IA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Socket set
Since i knew the filter was cleared of obstructions I knew the code issue was something more serious. After consulting with local repair reps I decided that the drain pump was beginning to slow down causing the faults. First, I took the lower front panel off the front of the washing machine so that I could drain the water out of the plum
... Read more
bing. After draining the water out of the pump into a pan, I went ahead and then lifted the front of the washer (and dryer on top of it) and tilted it back far enough so that my wife could place some blocking under the front of the washer. I did this so that I could access two screws on the bottom of the pump. First disconnect the wire socket connection to the motor. Make sure power is off before doing this. There is plastic clip holding the wires to the motor that may need a screwdriver to pry it apart for removal. There are two 1.5" long screws holding the pump to the frame that require at least 4" of space so that you can remove them with a socket. After removing the two pump screws I disconnected both pump hoses from the pump. This requires pliers for one clamp and screwdriver or nut driver for the other clamp. My machine originally came with one clamp that could not be removed, so I had to use a dremel with a stone to cut the clamp. You have to be careful to not damage the hose when cutting the clamp if it cannot be removed with tools. I replaced it with a 2" typical standard stainless steel hose clamp. Carefully wiggling the pump while pushing it to the side it will loosen up so that the front of the pump can be pulled up. One side needs to have the plastic plate pried apart from underneath and after removing it the pump will come free to lift out. Reverse the removal process for re-installation. It is a little tricky holding the squeeze clamp open while pulling the hose onto the pump, but it is not too difficult. Before putting the front panel on run one load of laundry to make sure there are no leaks. Once you find there are no leaks, then tilt the machine up and back to reattach the front panel. It is much easier to do it this way than with the machine on the floor since the panel screw are on the bottom of the panel at floor level.
Read less
Was this helpful?
Thank you for voting!