11025 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The upper bearing in the gearcase became rusty & very noisy due to shaft seal leakage.
22 of 26 people
found this instruction helpful.
-
Craig from ANAHEIM, CA
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Changing the gear case is a basic R and R operation since the gear case is a complete assembly riveted together. It is a bit challenging though getting to it because you have to totally disassemble the entire washer nearly every nut, bolt and screw. Fortunately the washer is fairly easy to work on and I am very mechanically inclined, but
... Read more
I did cheat a bit by watching some U-tube videos first. I couldn't find the same exact model washer as mine on U-tube but there were enough similar units to obtain the basic procedure. A thing I do when disassembling things is to take pictures of the way it's put together before removing stuff. It goes without saying that you first have to disconnect the power, the water hoses and it helps to get the washer out away from the wall so you can work around it. You have to remove the top, back panels, and the inner and outer tubs first. After removing the inner and outer tubs I turned the washer upside down in order to gain access to the gear case so I wouldn't have to stand on my head or lay down. Remove everything attached to the gear case (take picture) and use a strap wrench (or a strong friend) to hold the large pulley while removing the retaining nut. To remove the condenser (large round thing in black plastic retainer) rotate it counter clockwise and lift out, it doesn't snap out. I was very happy to see that the new gear case came with the shaft seal already installed so with a small amount of liquid dish soap around the outside of the rubber it allowed a nice slip fit back into the outer tub. All the parts that were removed pretty much will only fit one way so you don't have to worry too much about how everything goes back together. After reassembly and hooking up the washer again be sure to perform the calibration procedure before you turn on the water. Instructions came in the box with the gear case. Here is a side bar: I am 76, my grandson and I replaced the gear case in just a few hours, It's no big deal. Now for the interesting part, when I ordered the replacement gear case by the old part number I was told it had been superseded by a new number so when the new unit arrived I discovered that the shaft and seal looked different so hopefully the water leaking into bearing won't happen again. I was going to drill the old gear case apart and replace the bad bearing so I am glad I didn't because the shaft and seal would continue to leak and ruin the bearing again so don't try that. One thing I would like to mention about this company from which I ordered the part was the amazing delivery, only 36 hours. I ordered the part Sunday evening late and Tuesday morning early it arrived. Wow, blew me away, also I live in California and apparently the company is in Nova Scotia, no sales tax, Woo Hoo.
Read less
Was this helpful?
Thank you for voting!
Water in washer would continue to fill and overflow
22 of 26 people
found this instruction helpful.
-
Steve K. H. Chun from Redwood City, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Read on Internet to diagnose and get at part.
Luckly they sent new fill hose along with level control switch
as that was problem. Visually there was no
kink or blockage. Upon removing hose, I discovered
a slit on hose which did not allow pressure
to actuate diaphram. I installed new switch
and never thought t ... Read more o return as savings instead
of calling repairman was a no brainer !!!
Word of caution " never force"when removing or
installing a part. It should be easy Steve, Ca.
Luckly they sent new fill hose along with level control switch
as that was problem. Visually there was no
kink or blockage. Upon removing hose, I discovered
a slit on hose which did not allow pressure
to actuate diaphram. I installed new switch
and never thought t ... Read more o return as savings instead
of calling repairman was a no brainer !!!
Word of caution " never force"when removing or
installing a part. It should be easy Steve, Ca.
Read less
Was this helpful?
Thank you for voting!
valves allowed water to overflow during the rinse cycle, sometimes took forever to fill.
22 of 26 people
found this instruction helpful.
-
Sam from Robertsville, MO
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I removed the screws holding the control unit down, removed a couple at the rear,
Disconnected the electrical clip that plugs into the top, under the control unit.
This allows enough slack to pivot it ( the control unit) upside down and get it out of the way enough to remove the spring clips that hold the top to the back.
... Read more >Popped out the two clips that hold the back to the top.
Pulled the back out, up until the plastic soap dispenser , (which is attached to the back) hits under the lip of the top.
This does not allow enough room to get to the valves.
I finally figured out you have to lift the entire top up high enough to clear the back while pulling it ( the back) out.
Disconnected the hose clamp, electric connectors, installed the new valves into the supplied mounting plate replaced the valves .
Re -connected the hose and electric connectors and re assembled the back.
The only problem I had was when one of the spring retainers that hold the back to the top popped off and fell inside the unit, which forced me to remove everything including the back bottom screws, which caused the sides to pop off, the mounting ears , which are attached to the back,
Took some finesse but finally retrieved the spring clamp and finished everything back together.
It was a bit tricky keeping the plastic gaskets between the back and the sides from falling inside as I reassembled it.
But all is well, and would have been more difficult without the expierence written by others who posted, on the site.
Thank you to all, for the help.
I hope my efforts will help someone else.
Disconnected the electrical clip that plugs into the top, under the control unit.
This allows enough slack to pivot it ( the control unit) upside down and get it out of the way enough to remove the spring clips that hold the top to the back.
... Read more >Popped out the two clips that hold the back to the top.
Pulled the back out, up until the plastic soap dispenser , (which is attached to the back) hits under the lip of the top.
This does not allow enough room to get to the valves.
I finally figured out you have to lift the entire top up high enough to clear the back while pulling it ( the back) out.
Disconnected the hose clamp, electric connectors, installed the new valves into the supplied mounting plate replaced the valves .
Re -connected the hose and electric connectors and re assembled the back.
The only problem I had was when one of the spring retainers that hold the back to the top popped off and fell inside the unit, which forced me to remove everything including the back bottom screws, which caused the sides to pop off, the mounting ears , which are attached to the back,
Took some finesse but finally retrieved the spring clamp and finished everything back together.
It was a bit tricky keeping the plastic gaskets between the back and the sides from falling inside as I reassembled it.
But all is well, and would have been more difficult without the expierence written by others who posted, on the site.
Thank you to all, for the help.
I hope my efforts will help someone else.
Read less
Was this helpful?
Thank you for voting!
tub off center, rubbing on outer tub in spin
21 of 24 people
found this instruction helpful.
-
Charles from Rose Bud, AR
- A Bit Difficult
- 1- 2 hours
-
Pliers
turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.
Washer works great now.
Was this helpful?
Thank you for voting!
The support sprint had broke which left the basin unleveled so water would leak behind the basin and onto the floor
36 of 69 people
found this instruction helpful.
-
Michael from Newark, DE
- Really Easy
- Less than 15 mins
I replaced the broken support spring and the problem was fixed
Was this helpful?
Thank you for voting!
I bought a used washer from a friend and they had cut the drain hose short .
25 of 38 people
found this instruction helpful.
-
Francis from Yuba City, CA
- Really Easy
- 30 - 60 mins
-
Pliers
I got a pair of channel lock pliers and took off clamp on the hose, after laying wash machine on it's side, poped off a few little clips and replaced the hose, and now everything works perfect.
Was this helpful?
Thank you for voting!
Although the motor was running, washer wouldn't agitate or spin.
20 of 24 people
found this instruction helpful.
-
Thomas from Commack, NY
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
After disconnecting the electrical supply, first remove the two screws at either end of the control panel and fold it back away from the washer top. Then, unplug the electrical lid switch connection. Now, remove the two clips at either end on top to disconnect the housing from the washer back and chassis. The motor is sandwiched betwee
... Read more
n the water pump in the front and transmission at the rear. The Direct Drive Coupling connects the rear motor shaft to the transmisson. After you have taken the outter portion of the washer off, remove the two snap clips that hold the water pump in place and slide the pump off the front shaft. Best to also disconnect the upper hose connection so the pump can be moved out of the way. Caution though, remaining water in tub will drain out. Now remove the two screws that hold the clips in place which secure the motor to the transmission. Careful, as the old Direct Drive Coupling is probably destroyed, the clips are the only thing holding the motor in place and the motor needs to be supported so it won't drop to floor when the clips are removed. Be careful not to lose the four rubber grommets which sit between the motor and transmission bracket. After motor is on floor remove the old plastic slip-on direct drive coupling discs from both the motor and transmission shafts. The new replacement discs have steel centers which do not slide onto the shafts as easily as the old plastic ones did. I had to tap the center steel portion onto the shafts using a hammer and a deep wall socket the same width as the steel portion of the disc. Be careful! I'm sure that tapping the plastic portion of the disc to properly seat it on the shaft will break it away from the steel portion. In my case, It took me several attempts to completely seat the new discs. I had to do quite a bit of tapping to get the discs seated far enough onto the shafts so that the motor slipped easily against the transmission bracket grommets and the retainer clips snapped back into place easily. Reassembly is simply reversing the steps you took when taking the unit apart. Before putting the outter housing back in place, I checked to make sure everything was running smoothly by jumping out the electrical snap-in connection for the lid switch and running the machine in the spin cycle. Remember, if you don't jump out the lid switch and just try to test the unit in the aggitate cycle, the machine has to first fill with water.
Read less
Was this helpful?
Thank you for voting!
stopped working only filled with water.
20 of 24 people
found this instruction helpful.
-
Christa J from ElDorado Springs, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Fast simple and supper easy! Please do not waist your time or money on repairmen that rip you off. You are garunteed all the way or your money back from Parts Select. Go to your model number than read a few stories of others to better pin point your problem then order part and your item will ship fast I had my part on the 2nd day of the
... Read more
order. Do not be fooled you can do it easily! I have order twice and both items went smoothly and took less then 10 minutes to put in. Thanks Parts Select for making it possible for the little guys and supporting them and not the big rip off scammers. I will be back when needed. May you continue in your good deed! C.S.
Read less
Was this helpful?
Thank you for voting!
Water level was low in the washer
21 of 27 people
found this instruction helpful.
-
Anil from Redmond, WA
- Difficult
- 15 - 30 mins
-
Screw drivers
I had read many sites describing the issue of water level being low in the washer. Many people had suggested that changing the water level switch fixes the problem. So I ordered the part from PartSelect.com and it came promptly within a few days.
1. Disconnect the power to the washer.
2. Pull on the knob that controls th ... Read more e water level and remove it.
3. Remove the 2 screws on the bottom of the control panel.
4. Give the front portion of the control panel a small yank and pull it forward, around and upward. (It is hinged on the top, so it swings out)
5. Now you have access to the water level switch.
6. Press the clip and turn the switch a quarter of a turn and it will come off the panel.
7. Pull the wire connected to the switch and remove it.
8. Pull the air tube connected to the switch and remove it.
9. Use the new water level switch and reverse the process.
10. Plug the washer back in an everything works great!
1. Disconnect the power to the washer.
2. Pull on the knob that controls th ... Read more e water level and remove it.
3. Remove the 2 screws on the bottom of the control panel.
4. Give the front portion of the control panel a small yank and pull it forward, around and upward. (It is hinged on the top, so it swings out)
5. Now you have access to the water level switch.
6. Press the clip and turn the switch a quarter of a turn and it will come off the panel.
7. Pull the wire connected to the switch and remove it.
8. Pull the air tube connected to the switch and remove it.
9. Use the new water level switch and reverse the process.
10. Plug the washer back in an everything works great!
Read less
Was this helpful?
Thank you for voting!
Lid safety switch defective . Lid would not lock allowing washer operation.
19 of 21 people
found this instruction helpful.
-
Garry from CANON CITY, CO
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Remove small screws on back of top on both sides, slide top forward. No need to remove water hoses. Lift top up to expose switch safety mechanism (black plastic) on front underside of top. Undo screws holding switch mechanism. remove plate cover from back of top and unplug wiring harness. Thread new wireing harness and plug through hole
... Read more
in top and plug in to plug receptor.
Read less
Was this helpful?
Thank you for voting!
The washer was displaying FL code, and not draining
19 of 22 people
found this instruction helpful.
-
chris from davison, MI
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
1) Pull the washer away from the wall
2) Lean the washer back so it is balanced and you can see the bottom
3) Remove 3 screws along the front edge of bottom plate
4)Remove plate, exposing the pump
5)Remove 2 clips that hold pump to motor
6)Place the deepest pan you can fit under pump
7)Loosen hose clamp, pull ... Read more hose SLOWLY from pump
8)Drain as carefully as possible (its a couple /few gallons)
9)Remove second hose clamp, set pump aside
10)Remove three bolts holding in motor
11)Remove small plastic anchor that goes through frame
12)Follow wires to plastic plug. It is easier to remove the closer to you, then push remaining side of the plug through the mount.
13) Reverse the steps, the new pump motor will go in as one unit because of the torque screws(no clips).
Note: I tried to save the old motor because I could see the clog inside of it. After freeing it up, I re-assembled it ,ran the washer and got the FL code again, So I had to remove it again and replace it with the new one. Now it has been through about
10 loads and is working well.
2) Lean the washer back so it is balanced and you can see the bottom
3) Remove 3 screws along the front edge of bottom plate
4)Remove plate, exposing the pump
5)Remove 2 clips that hold pump to motor
6)Place the deepest pan you can fit under pump
7)Loosen hose clamp, pull ... Read more hose SLOWLY from pump
8)Drain as carefully as possible (its a couple /few gallons)
9)Remove second hose clamp, set pump aside
10)Remove three bolts holding in motor
11)Remove small plastic anchor that goes through frame
12)Follow wires to plastic plug. It is easier to remove the closer to you, then push remaining side of the plug through the mount.
13) Reverse the steps, the new pump motor will go in as one unit because of the torque screws(no clips).
Note: I tried to save the old motor because I could see the clog inside of it. After freeing it up, I re-assembled it ,ran the washer and got the FL code again, So I had to remove it again and replace it with the new one. Now it has been through about
10 loads and is working well.
Read less
Was this helpful?
Thank you for voting!
washer did not agitate
21 of 28 people
found this instruction helpful.
-
Eric from Jacksonville, FL
- Really Easy
- Less than 15 mins
-
Socket set
popped thecap off removed the bolt, pulled agitator off replaced cogs(dogs) then put back together. works like new.whole time took about 10-15 min. saved my self 150.00 by not hireing repair man.
Other Parts Used:
Was this helpful?
Thank you for voting!
washer wouldn't start up after filling & closing lid
20 of 26 people
found this instruction helpful.
-
Jeremy from Marengo, IA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
First I loosened the 2 screws on the outside of the top control assembly with a philips screwdriver. Then I took out the 2 other screws toward the top on the back with a socketwrench.Next I removed the top so I could access the switch. After that I removed the broken switch and unhooked from wire hareness. I then hooked up the new switch
... Read more
and snapped into place. Last I put the top back on and screwed into place.
Read less
Was this helpful?
Thank you for voting!
Top Half of Agitator would not function without appying sideways pressure
18 of 21 people
found this instruction helpful.
-
Donald from Fredericksburg, VA
- Really Easy
- 15 - 30 mins
-
Socket set
Heard about the website... 1 minute to find it, 10 minutes to order new cogs... 3 day wait for new parts... Rec'd Fedex, 15 minutes total to pull the agitator cover (bleach dispenser) then the bung cover with o-ring (just lift out) expose bolt, unskrew and remove top portion of agitator or entire agitator if it's easier. Seperate, remo
... Read more
ve black cog holder (slides up the spindle) and replace cogs one at a time just like the old ones. Reassemble in reverse and you are back in business. Saved the $75 deductible on my home appliance warrenty. You guys are the best... cheers...
Read less
Was this helpful?
Thank you for voting!
Agitator was barely agitating. Making a clicking noise.
17 of 18 people
found this instruction helpful.
-
Charmaine from Slidell, LA
- Easy
- 15 - 30 mins
-
Socket set
Removed agitator cap. Removed bolt inside with socket wrench. Located plastic cogs Pulled out old cogs and slid in new cogs and put back together and works great. Easy to take apart and put back together. Very cheap repair. Cogs less that $4.00 plus shipping. Shipped next working day.
Was this helpful?
Thank you for voting!