11025 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
hoses had holes in them
18 of 25 people
found this instruction helpful.
-
Sharon from Dallas, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Put clamps on hose end and then used some dishsoap on the inside of the hose to make pushing them into place easier once in place I placed the clamp in correct spot and used a screwdriver to tighten the clamps.
Other Parts Used:
Was this helpful?
Thank you for voting!
leaking drain pump. Obviously a common problem with this washer
15 of 17 people
found this instruction helpful.
-
John from Solana Beach, CA
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench (Adjustable)
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the we
... Read more
bsite parts diagram and whole website design is good.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Smelled a burning odor occasionally
17 of 23 people
found this instruction helpful.
-
Paul from E NORTHPORT, NY
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set, Wrench (Adjustable)
First, I checked the belt before ordering and then decided to order the belt, capacitor, and clutch assembly (if I needed to replace). I replaced the belt noticing the older belt came right off and new one was tighter going on. I replaced the capacitor since I had it handy and it can be known to cause this smell also. After setting wash
... Read more
er back up and started a cycle I noticed the spin cycle would not start properly so I thought maybe the capacitor (new one) was faulty or just not the exact match even though it was said to be. I replaced my older capacitor back on and again ran cycle and it ran great. Thus I decided to send the parts which were not used. I would recommend this site as I have used them in the past before on other items. They ship fast and have a great return policy if parts not used.
Read less
Was this helpful?
Thank you for voting!
Washer lid would not release
18 of 26 people
found this instruction helpful.
-
Michael from BURLINGTON, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug washer. Remove 4 screws from the small plates that hold top to body of washer. Remove cover plate from back of top. Lift top from base and support it on its back. Remove lid lock mechanism. Unplug connector from its socket at the back of the lid. In reverse order install the new lid latch,
Was this helpful?
Thank you for voting!
Unbalanced washer
14 of 14 people
found this instruction helpful.
-
Joseph from CLARKSVILLE, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Unplugged, Removed rear screws
Pulled lid forward, and lifted, rested against wall
Removed rim piece, agitator, my wife cleaned them
Removed, replaced suspension rods one at a time, replaced plastic seats as I went
Removed old hub, cleaned and lubed gear and replaced, used a towel so screws did fall in the basin holes ... Read more
Put back together
Used instructions to recalibrate
Tested it out, good to go
notes….the old parts don’t really appear damaged to the untrained eye, probably should send the bumper padding with this kit, the recal instructions were money!
Pulled lid forward, and lifted, rested against wall
Removed rim piece, agitator, my wife cleaned them
Removed, replaced suspension rods one at a time, replaced plastic seats as I went
Removed old hub, cleaned and lubed gear and replaced, used a towel so screws did fall in the basin holes ... Read more
Put back together
Used instructions to recalibrate
Tested it out, good to go
notes….the old parts don’t really appear damaged to the untrained eye, probably should send the bumper padding with this kit, the recal instructions were money!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washmachine wouldn't spindry
15 of 17 people
found this instruction helpful.
-
Chuck from South Holland, IL
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers, Socket set, Wrench set
I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.
Was this helpful?
Thank you for voting!
No cold water supply/slow cold water fill
14 of 15 people
found this instruction helpful.
-
Andrew from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs a
... Read more
nd moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.
Read less
Was this helpful?
Thank you for voting!
Washer worked fine but wouldn't spin. Hot smell. I could turn tub by hand to help it get started and it would spin okay. Silver clutch cover was very hot to touch.
17 of 24 people
found this instruction helpful.
-
Kevin from Disputanta, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's
... Read more
lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.
Read less
Was this helpful?
Thank you for voting!
my cold water did not run in the machine and it would not rinse
15 of 18 people
found this instruction helpful.
-
TONYA from DISTRICT HEIGHTS, MD
- Easy
- Less than 15 mins
-
Screw drivers
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Was this helpful?
Thank you for voting!
washer overflowing
17 of 24 people
found this instruction helpful.
-
GREIG from CARTERSVILLE, GA
- Easy
- Less than 15 mins
-
Screw drivers
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.
I respect that electrical parts are non-returnable as I am in the auto parts business.
Was this helpful?
Thank you for voting!
Water Inlet Valve
14 of 16 people
found this instruction helpful.
-
Ron from Hibbing, MN
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The reason it took as long as it did was because the job is not in line as the work I normally do.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water ... Read more for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
It would be a fairly easy job for an experienced repairman. (Taking the back off the washer was time consuming for me) The rest of the job was easy as the part was a perfect fit.
I remember having a problem blending hot/cold water ... Read more for some time. Most recently, while washing a load the water did not want to shut off. I can't remember how I diagnosed the water not shuting off as a problem along with the water temp control, but it is now repaired.
With the new valve installed, water temp select is now OK and the water now shuts off as normal.
Read less
Was this helpful?
Thank you for voting!
water leaking from pump
15 of 19 people
found this instruction helpful.
-
michael from westmoreland city, PA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Th ... Read more e corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
Read less
Was this helpful?
Thank you for voting!
Broken seal
15 of 19 people
found this instruction helpful.
-
Samuel from Grass Valley, CA
- Really Easy
- Less than 15 mins
Removed old, pressed on new. This is no story but the reason I am writing is to say how impressed I was with the ease of using your Web site to find my part and of your spectacularly fast service.
Was this helpful?
Thank you for voting!
Screeching noise when starting the washing cycle. Especially with heavy loads.
15 of 19 people
found this instruction helpful.
-
Armando from UNION CITY, CA
- Really Easy
- Less than 15 mins
-
Socket set
The belt in this model is underneath the washing machine. Disconnect water lines and power cords, set up the drain hose in a bucket to avoid water spilling on the floor, tip the washing machine on its back, remove two bolt screws holding the plastic covering the belt, remove the old belt, and install the new one.
Was this helpful?
Thank you for voting!
Washer would not Agitate or spin out. Also noticed an oil leak.
14 of 16 people
found this instruction helpful.
-
Jonathan from BRANDON, VT
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
I followed instructions provided from Parts Select for removing and replacing the coupler assembly, and also instructions for changing the clutch assembly. I also took it's transmission apart (socket set and flat screwdriver required), drained the old oil, cleaned it, added new 90W gear oil. The instructions covered the swapping of parts
... Read more
very well. Cleaning up the oil spill took as long as changing the parts.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!